Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COMBINATION SWITCH
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0244775 COMBINATION SWITCH G

HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84720J 1.INSPECT PATTERN SELECT SWITCH ASSEMBLY (for LHD)

a.

Inspect EV mode switch

i.
A338088C16
2.219,1.917 2.073,1.552 true 1.771,1.938 1.885,1.552 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 1.719,1.958 1.844,2.115 0.125,0.156 10 false S 2.219,1.958 2.365,2.135 0.146,0.177 10 false E
*a Component without harness connected
(Pattern Select Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
10 (S) - 9 (E) EV mode switch being pushed and held Below 50 Ω
EV mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly.



b.

Inspect DRIVE mode switch

i.
A338088C24
2.219,1.917 2.073,1.552 true 1.896,1.167 2.115,0.49 2.115,0.49 2.323,0.49 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 2.375,0.427 2.729,0.604 0.354,0.177 10 false DRV 2.219,1.958 2.365,2.135 0.146,0.177 10 false E
*a Component without harness connected
(Pattern Select Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (DRV) - 9 (E) DRIVE mode switch being pushed and held Below 50 Ω
DRIVE mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly.



c.

Inspect VAS OFF switch (w/ Vehicle Proximity Notification System)

i.
A338088C20
1.094,1.917 1.188,1.542 true 1.365,1.167 1.583,0.49 1.583,0.49 1.792,0.49 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 1.844,0.427 2.198,0.604 0.354,0.177 10 false IG 0.969,1.938 1.323,2.156 0.354,0.219 10 false ECU
*a Component without harness connected
(Pattern Select Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (IG) - 14 (ECU) VAS OFF switch being pushed and held Below 50 Ω
VAS OFF switch not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly.



d.

Inspect illumination

i.
A338088C25
1.26,1.927 1.354,1.552 true 2.073,1.167 2.292,0.49 2.292,0.49 2.5,0.49 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 2.563,0.427 2.917,0.604 0.354,0.177 10 false ILL- 1.146,1.958 1.479,2.146 0.333,0.188 10 false ILL+
*a Component without harness connected
(Pattern Select Switch Assembly)


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the pattern select switch assembly.

OK:
Measurement Condition Specified Condition
Auxiliary Battery positive (+) → 13 (ILL+)
Auxiliary Battery negative (-) → 2 (ILL-)
Illuminates


If the result is not as specified, replace the pattern select switch assembly.



Hide 84720J 2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (for RHD)

a.

Inspect EV mode switch

i.
A338088C12
2.219,1.917 2.073,1.552 true 1.885,1.167 1.615,0.469 1.615,0.469 1.448,0.469 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 1.302,0.417 1.427,0.573 0.125,0.156 10 false S 2.219,1.958 2.365,2.135 0.146,0.177 10 false E
*a Component without harness connected
(Pattern Select Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (S) - 9 (E) EV mode switch being pushed and held Below 50 Ω
EV mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly.



b.

Inspect DRIVE mode switch

i.
A338088C21
2.219,1.917 2.073,1.552 true 1.781,1.927 1.885,1.563 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 1.656,1.948 2.01,2.125 0.354,0.177 10 false DRV 2.208,1.948 2.354,2.125 0.146,0.177 10 false E
*a Component without harness connected
(Pattern Select Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
10 (DRV) - 9 (E) DRIVE mode switch being pushed and held Below 50 Ω
DRIVE mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly.



c.

Inspect illumination

i.
A338088C25
1.26,1.927 1.354,1.552 true 2.073,1.167 2.292,0.49 2.292,0.49 2.5,0.49 true 0.198,0.083 0.635,0.635 0.438,0.552 10 false *a 2.563,0.427 2.917,0.604 0.354,0.177 10 false ILL- 1.146,1.958 1.479,2.146 0.333,0.188 10 false ILL+
*a Component without harness connected
(Pattern Select Switch Assembly)


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the pattern select switch assembly.

OK:
Measurement Condition Specified Condition
Auxiliary Battery positive (+) → 13 (ILL+)
Auxiliary Battery negative (-) → 2 (ILL-)
Illuminates


If the result is not as specified, replace the pattern select switch assembly.