Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT CLEARANCE SONAR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244854 INTELLIGENT CLEARANCE SONAR SYSTEM D

PARK ASSIST / MONITORING  INTELLIGENT CLEARANCE SONAR SYSTEM  CALIBRATION  


NOTICE:

When any of the following parts have been replaced, perform adjustment shown in the following table. If not, the intelligent clearance sonar system may not operate correctly.


PRECAUTION (PROCEDURE 1)


a.

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intelligent clearance sonar system removal/installation are shown below.

For the installation location of the ultrasonic sensors, refer to Parts Location.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>PARTS LOCATION

Part Name Operation Adjustment Item Proceed to
Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize intelligent clearance sonar system)*3 Procedure 4
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Front bumper assembly
·

Replacement

·

Installation position of the front bumper assembly changes because of the removal and installation of the front bumper assembly


Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Rear bumper assembly
·

Replacement

·

Installation position of the rear bumper assembly changes because of the removal and installation of the rear bumper assembly


Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Clearance warning ECU assembly Replacement Ultrasonic sensor detection angle Procedure 2, 3
Steering angle neutral point Procedure 4
Bumper type registration
Ultrasonic sensor detection angle registration
Ultrasonic sensor*1*2
·

Removal and installation

·

Replacement


Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
An ultrasonic sensor becomes misaligned Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
An ultrasonic sensor is subjected to impact Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Auxiliary battery Cable is disconnected from the negative (-) auxiliary battery terminal Steering angle neutral point*3 Procedure 4

*1: If a front side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform Registration.

*2: If a rear side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform Registration.

*3: The steering sensor zero point can also be calibrated by driving the vehicle.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>INITIALIZATION




PREPARATION (PROCEDURE 2)


a.

Preparation

·

Digital angle gauge

·

Digital angle gauge attachment

·

Masking tape (To prevent damage)

·

A level


SST
09989-00020  


b.

Confirm levelness of floor surface.

i.

Place a bubble level on a level surface and confirm that the bubble is centered.

NOTICE:

Make sure that there is no gravel, sand, etc., and that the surface is not undulating.


HINT:

By adjusting the direction of the bubble level, it is possible to find a position where the bubble is centered.


E344401


ii.

Turn on the digital angle gauge.


iii.

Place the digital angle gauge in the same location and direction as that of the bubble level where the levelness of the surface was confirmed.

NOTICE:

Confirm that the location and direction of the digital angle gauge is exactly the same as that of the bubble level.


E345346C01
1.667,1 2.135,0.74 false 1.448,2.635 2.031,2.938 false 5.594,3.26 6.125,3.49 false 5.635,1.49 6.167,1.719 false 6.24,1.698 6.552,1.896 0.313,0.198 10 false *a 2.094,2.906 2.406,3.104 0.313,0.198 10 false *b 6.208,3.479 6.521,3.677 0.313,0.198 10 false *a 2.167,0.615 2.479,0.813 0.313,0.198 10 false *a
*a Digital Angle Gauge *b Level



iv.

Press the "ZERO" switch to memorize the zero point (perfectly level).

NOTICE:

Make sure that the digital angle gauge does not move when pressing the switch. If the digital angle gauge moves when the switch is pressed, an incorrect zero point may be memorized and it will not be possible to accurately check for levelness.



v.

Using the digital angle gauge in which the zero point (perfectly level) has been memorized, measure the angle of the floor surface at the 4 positions at the front of the vehicle and the 4 positions at the rear of the vehicle as shown in the illustration.

NOTICE:
·

Always position the digital angle gauge in the direction shown in the illustration.

·

Make sure that there is no gravel, sand, etc., and that the floor surface is not undulating.

·

When measuring the angle of the floor surface, avoid uneven areas such as joints between tiles.



HINT:

If necessary, the digital angle gauge can be placed anywhere within the specified area when measuring the angle of the floor surface for positions A, C, F and H.


E345185C02
0.052,4.323 1.25,4.583 1.198,0.26 10 false 250 mm (9.84 in.) 0.594,2.313 0.802,2.479 0.208,0.167 10 false A 1.229,4.333 2.396,4.583 1.167,0.25 10 false 100 mm (3.94 in.) 1.094,2.313 1.302,2.479 0.208,0.167 10 false B 0.583,3.594 0.792,3.76 0.208,0.167 10 false C 1.104,3.594 1.313,3.76 0.208,0.167 10 false D 5.771,2.302 5.979,2.469 0.208,0.167 10 false E 6.208,2.302 6.417,2.469 0.208,0.167 10 false F 6.25,3.594 6.438,3.792 0.188,0.198 10 false H 5.76,3.594 5.948,3.792 0.188,0.198 10 false G 0.208,0.573 1.375,0.833 1.167,0.26 10 false 50 mm (1.97 in.) 4.844,4.344 5.958,4.625 1.115,0.281 10 false 100 mm (3.94 in.) 6.031,4.344 7.125,4.635 1.094,0.292 10 false 250 mm (9.84 in.) 1.354,0.583 2.417,0.854 1.063,0.271 10 false 50 mm (1.97 in.) 4.719,0.563 5.813,0.771 1.094,0.208 10 false 50 mm (1.97 in.) 5.938,0.563 7,0.833 1.063,0.271 10 false 50 mm (1.97 in.) 0.24,0.188 1.51,0.438 1.271,0.25 10 false Position A and C: 4.729,0.177 6,0.427 1.271,0.25 10 false Position F and H:
V100155

Confirmation Area - -



vi.

Using the following worksheet, calculate the average of the measurements taken at the 4 positions in front of the vehicle, and calculate the average of the measurements taken at the 4 positions behind the vehicle. Confirm that the front measurement average and the rear measurement average are more than approximately 0.37 degrees. Also, confirm that the front measurement average and the rear measurement average is 0.2 degrees or more.

NOTICE:

If the front measurement average and the rear measurement average are not more than approximately 0.37 degrees or the difference between the front measurement average and the rear measurement average is less than 0.2 degrees, choose another work area as it is not possible to accurately check the installation angle of the sensors.


Worksheet:
E344824E02
0.906,0.427 1.063,0.625 0.156,0.198 10 false A 1.281,0.427 1.438,0.625 0.156,0.198 10 false B 1.281,1.635 1.438,1.833 0.156,0.198 10 false D 5.76,0.417 5.917,0.615 0.156,0.198 10 false E 6.135,0.417 6.292,0.615 0.156,0.198 10 false F 5.75,1.635 5.906,1.833 0.156,0.198 10 false G 6.125,1.635 6.281,1.833 0.156,0.198 10 false H 0.906,1.635 1.063,1.833 0.156,0.198 10 false C 0.271,2.167 1.365,2.396 1.094,0.229 10 false 250 mm (9.84 in.) 1.438,2.177 2.698,2.563 1.26,0.385 10 false 100 mm (3.94 in.) 5.802,2.177 6.885,2.406 1.083,0.229 10 false 250 mm (9.84 in.) 1.083,3.292 1.354,3.479 0.271,0.188 10 false A 4.958,2.865 5.583,3.063 0.625,0.198 10 false Rear side 1.563,2.865 2.281,3.083 0.719,0.219 10 false Front side 1.083,4 1.354,4.208 0.271,0.208 10 false C 2.76,4 3.031,4.188 0.271,0.188 10 false D 2.76,3.292 3.031,3.479 0.271,0.188 10 false B 4.385,3.292 4.656,3.479 0.271,0.188 10 false E 4.385,4.01 4.656,4.198 0.271,0.188 10 false G 6.063,3.292 6.333,3.479 0.271,0.188 10 false F 6.073,4 6.344,4.188 0.271,0.188 10 false H 0.302,5.667 3.167,5.896 2.865,0.229 10 false Both of the following conditions are met: 3.615,4.75 7.031,5.115 3.417,0.365 10 false (E + F + G + H)/ 4 = rear measurement average 0.365,5.958 6.635,6.354 6.271,0.396 10 false - The difference between the front measurement average and the rear measurement average is less than 0.2 degrees. 1.333,6.906 4.229,7.146 2.896,0.24 10 false OK: Proceed to the next step. 0.563,7.344 6.635,7.615 6.073,0.271 10 false (Front measurement average + Rear measurement average)/ 2 = Floor surface inclination 0.271,4.75 3.594,4.99 3.323,0.24 10 false (A + B + C + D)/ 4 = front measurement average 0.688,8.292 6.844,8.542 6.156,0.25 10 false After calculating the floor surface inclination, proceed to "Calibrate the digital angle gauge". 4.615,2.177 5.74,2.5 1.125,0.323 10 false 100 mm (3.94 in.) 3.729,6.917 6.625,7.156 2.896,0.24 10 false NG: Choose another work area. 0.365,6.521 6.5,6.917 6.135,0.396 10 false - The front measurement average and the rear measurement average are not more than approximately 0.37 degrees.


vii.

Average the front measurement average and the rear measurement average, then round the answer to 1 decimal place (E.g. 0.0927 degrees is rounded to 0.1 degrees) to obtain the floor surface inclination value.


viii.

Calibrate the digital angle gauge

Adjust the angle of the digital angle gauge until it reads the same value of floor surface inclination, then press the "ZERO" switch to memorize the zero point (level with floor surface).

NOTICE:

Before pressing the "ZERO" switch, confirm that the digital angle gauge reading is positive if the floor angle inclination is positive, and negative if the floor angle inclination is negative.


E344822E02
0.865,1.844 1.688,1.531 true 0.802,0.958 1.698,1.385 true 4.188,2.125 6.323,2.521 2.135,0.396 10 false After calibrating, displays 90° when turned on its side 1.75,2.375 2.802,2.594 1.052,0.219 10 false Calibrating 0.604,0.885 0.958,1.052 0.354,0.167 10 false (+) 0.635,1.802 0.99,1.969 0.354,0.167 10 false (-)



c.
E345186E02
2.24,2.979 2.5,2.979 2.5,2.979 3.073,1.917 false 2.781,1.281 2.573,0.479 2.573,0.479 2.344,0.479 false 0.448,0.385 2.594,0.583 2.146,0.198 10 false Digital angle gauge attachment 1.385,2.885 2.344,3.083 0.958,0.198 10 false Masking tape

Prepare the digital angle gauge

i.

Attach the digital angle gauge attachment to the digital angle gauge.

SST
09989-00020  


ii.

Attach masking tape to the digital angle gauge attachment.



d.

Remove all luggage from the vehicle.


e.

Adjust the tire inflation pressure to the specified pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION




SENSOR HEIGHT AND ALIGNMENT INSPECTION (PROCEDURE 3)


HINT:

Check if the installation angle of each ultrasonic sensor is appropriate.


a.

Preparation

i.

Visually check that the bumper, grill and ultrasonic sensors are installed properly and are not damaged.

NOTICE:

If the bumper, grill or any ultrasonic sensor is not installed correctly, the calibration may not be able to be completed.



ii.

Check the tire pressures and adjust them if necessary.

Click hereGeneral>SPECIFICATIONS>TIRE / WHEEL>SERVICE DATA

NOTICE:
·

Ensure that the vehicle is level in an area with no wind.

·

Do not lean on the vehicle.

·

Do not do anything that may affect the level of the vehicle during the calibration, such as getting in or out of the vehicle, or adding or removing luggage.





b.

Sensor height and alignment inspection

E333744E04
1.5,0.438 1.615,0.438 1.615,0.438 1.646,1.083 false 5.51,1.208 5.74,0.771 5.74,0.771 5.917,0.771 false 5.531,1.635 5.771,1.729 5.771,1.729 5.948,1.729 false 0.896,1.083 1.073,1.083 1.073,1.083 1.646,1.76 false 5.427,0.813 5.438,0.094 5.438,0.094 5.656,0.094 false 1.531,2.229 1.729,2.229 1.729,2.229 1.813,2.01 false 1.76,0.365 1.667,0.365 1.667,0.365 1.813,0.802 false 5.427,2.031 5.729,2.417 5.729,2.417 5.573,2.417 false 0.021,0.021 2.927,0.219 2.906,0.198 10 false Ultrasonic Sensor Installation Location: 1.823,0.271 4.406,0.458 2.583,0.188 10 false Front Corner Ultrasonic Sensor RH 0.052,0.354 1.5,0.875 1.448,0.521 10 false Front Center Ultrasonic Sensor RH 0.052,1 0.875,1.615 0.823,0.615 10 false Front Center Ultrasonic Sensor LH 0.104,2.146 1.552,2.521 1.448,0.375 10 false Front Corner Ultrasonic Sensor LH 5.708,0.021 7.135,0.74 1.427,0.719 10 false Rear Corner Ultrasonic Sensor RH 5.969,0.688 6.74,1.271 0.771,0.583 10 false Rear Center Ultrasonic Sensor RH 6.031,1.656 6.823,2.229 0.792,0.573 10 false Rear Center Ultrasonic Sensor LH 3.448,2.344 5.854,2.552 2.406,0.208 10 false Rear Corner Ultrasonic Sensor LH


c.
E336425E02
0.458,2.333 1.313,1.052 true 0.198,2.365 0.833,2.833 0.635,0.469 10 false Center of Sensor 1.948,2.552 3.042,2.781 1.094,0.229 10 false Sensor Height

Measure the installation height of the sensors.

Standard Height (Front Bumper):
Sensor Location Sensor Height
Front Center Ultrasonic Sensor 512.5 to 582 mm (20.2 to 23.0 in.)
Front Corner Ultrasonic Sensor 441.7 to 513.7 mm (17.4 to 20.2 in.)

Standard Height (Rear Bumper):
Sensor Location Sensor Height
Rear Center Ultrasonic Sensor 541.6 to 613.6 mm (21.3 to 24.2 in.)
Rear Corner Ultrasonic Sensor 456.6 to 528.6 mm (18.0 to 20.8 in.)

NOTICE:

If the installation height of a sensor is not as specified, it may not be possible to measure the sensor angles correctly. If so, unload the vehicle and measure the installation height of the sensors again.


HINT:

Use the center of the sensor as the measuring point.



d.
E336426E02
1.438,1.229 1.135,0.844 1.135,0.844 0.969,0.844 true 1.708,1.542 2,0.969 2,0.969 2.146,0.969 true 1.781,1.646 1.917,2.344 1.917,2.344 2.135,2.344 true 2.188,0.875 3.375,1.292 1.188,0.417 10 true Digital angle gauge attachment 2.177,2.281 2.885,2.677 0.708,0.396 10 true Ultrasonic Sensor 0.115,0.771 0.896,1.156 0.781,0.385 10 true Digital angle gauge

Using the digital angle gauge, measure the angle of each sensor.

i.

Measure the angle of the front sensors as shown in the illustration.

NOTICE:

Ensure that the digital angle gauge is flush with the face of the sensor.



ii.
E345419E02
1.25,0.948 1.49,0.948 1.49,0.948 1.99,1.677 true 1.688,2.198 1.844,2.198 1.844,2.198 2.073,1.792 true 2.219,3.021 2.479,3.021 2.479,3.021 2.729,2.26 true 1.073,2.927 2.26,3.125 1.188,0.198 10 true Digital angle gauge 0.083,0.854 1.229,1.073 1.146,0.219 10 true Ultrasonic Sensor 0.417,2.104 1.635,2.469 1.219,0.365 10 true Digital angle gauge attachment

Measure the angle of the rear sensors as shown in the illustration.

NOTICE:

Ensure that the digital angle gauge is flush with the face of the sensor.



iii.
E345374E02
2.385,1.333 2.5,1.49 2.5,1.49 2.646,1.49 true 2.125,1.396 2.073,1.896 2.073,1.896 1.969,1.896 true 2.469,1.24 2.563,0.698 2.563,0.698 2.688,0.698 true 1.74,0.719 1.823,0.26 1.823,0.26 1.979,0.26 true 0.104,0.094 1.125,0.281 1.021,0.188 10 false For front: 0.031,1.813 1.927,2.073 1.896,0.26 10 false Digital angle gauge attachment 2.031,0.156 3.375,0.458 1.344,0.302 10 false Digital angle gauge 2.729,0.583 3.365,0.969 0.635,0.385 10 false Horizontal line 0.885,0.719 1.563,0.99 0.677,0.271 10 false + 0.917,1.552 1.25,1.75 0.333,0.198 10 false - 2.708,1.396 3.365,1.781 0.656,0.385 10 false Ultrasonic Sensor

E318150E02
0.75,1.615 0.844,1.615 0.844,1.615 0.906,1.375 true 2.656,0.625 2.552,0.625 2.552,0.625 2.49,1.229 false 2,0.24 1.833,0.24 1.833,0.24 1.563,0.729 false 1.448,1.917 1.333,1.917 1.333,1.917 1.167,1.417 true 0.104,0.094 1.344,0.49 1.24,0.396 10 false For rear: 2.344,1.521 2.74,1.719 0.396,0.198 10 false - 0.083,1.49 0.729,1.875 0.646,0.385 10 false Ultrasonic Sensor 2.323,0.771 2.719,0.948 0.396,0.177 10 false + 2.708,0.521 3.365,0.938 0.656,0.417 10 false Horizontal line 1.49,1.823 3.396,2.01 1.906,0.188 10 false Digital angle gauge attachment 2.052,0.167 3.385,0.458 1.333,0.292 10 false Digital angle gauge

Confirm that the angles of the sensors are as specified.

NOTICE:

The sensor angle is the measured sensor angle subtracted from 90°.


HINT:
·

The digital angle gauge should indicate 90° when turned on its side.

·

If the face of the sensor is tilted upwards, the sensor angle will be positive.



Standard Height (Front Bumper):
Sensor Location Installation Angle
Front Center Ultrasonic Sensor -3.8 to 6.1°
Front Corner Ultrasonic Sensor -3.0 to 6.9°

Standard Height (Rear Bumper):
Sensor Location Installation Angle
Rear Center Ultrasonic Sensor -3.2 to 6.7°
Rear Corner Ultrasonic Sensor -2.2 to 7.7°


iv.

If the angle or height of the sensors is not as specified, confirm that the installation is correct and then perform the inspection again.




REGISTRATION (PROCEDURE 4)


a.

Preparation

i.

Confirm that the following DTCs are not output.

System Proceed to
Intelligent Clearance Sonar System (Click here)
Simple Intelligent Parking Assist System (Click here)

NOTICE:

If DTC C1AF0, C1AF3, C1AF4, C1AF5, C1AF6, C1AEA or C168D are output at this point, it is not a malfunction. Proceed with the calibration.




b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / IPA/ICS/Clearance Sonar / Utility.

Body Electrical > IPA/ICS/Clearance Sonar > Utility
Tester Display
Intuitive P/A Detection/Steering Adjustment
50005 170 5402

f.

According to the display on the GTS, perform calibration.

HINT:

If "Battery or Steering Sensor" is selected, further calibration is not required. (Bumper type registration is not required.)



g.

Enter the bumper type using the GTS.

Bumper Type Value
Standard 1

HINT:

If the clearance warning ECU assembly is replaced or removed and installed, it is necessary to perform bumper type registration.



h.

Using the GTS, enter the measured sensor values.

NOTICE:

The sensor angle is the measured sensor angle subtracted from 90°.


HINT:

The digital angle gauge should indicate 90° when turned on its side.



i.

Disconnect the GTS from the DLC3.