Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244875 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  SYSTEM DESCRIPTION  


GENERAL


a.

The blind spot monitor system has the blind spot monitor function and RCTA function.

i.

Blind spot monitor function

·

The blind spot monitor function is a function that assists the driver in making the decision to change lanes. The function uses quasi-millimeter wave radar to detect vehicles that are traveling in an adjacent lane in the area that is not reflected in the outer rear view mirror assembly. The function advises the driver of the existence of a vehicle by illuminating the outer rear view mirror indicator on the outer rear view mirror assembly.

·

If the turn signal switch is operated while the outer rear view mirror indicator on an outer rear view mirror assembly is illuminated, the indicator starts blinking to give additional warning to the driver.



ii.

RCTA function

·

The RCTA function is a function that informs the driver of an approaching vehicle from diagonally behind. The function uses quasi-millimeter wave radar to detect the positions of and relative speed to a vehicle. When the function determines that a vehicle is approaching this vehicle, this function informs the driver of it using the indicators and buzzer.





FUNCTION OF COMPONENTS


Component Function
Blind Spot Monitor Sensor
·

Consists of a 24 GHz radar module and an integrated processing module.

·

Illuminates or blinks the outer rear view mirror indicator on the outer rear view mirror assembly.

·

Sounds the RCTA buzzer (blind spot monitor buzzer) when the RCTA function is operating. (w/ RCTA)

·

Changes the outer rear view mirror indicator on the outer rear view mirror assembly from illuminated to blinking when a turn signal switch operation signal is received from the meter circuit plate with the blind spot monitor function operating.

·

Displays the RCTA icon on the multi-information display when the RCTA function is operating. (w/ RCTA)


Outer Rear View Mirror Assembly
·

Outer Rear View Mirror (Outer Rear View Mirror Indicator)


Turns on or blinks the indicator based on a signal from the blind spot monitor sensor.
Steering Pad Switch Assembly Enables, disables or cuts off the operation of the blind spot monitor system by transmitting the switch operation signal to the meter circuit plate.
RCTA Buzzer (Blind Spot Monitor Buzzer)
(w/ RCTA)
Sounds based on a signal from the blind spot monitor sensor.
Meter Circuit Plate
·

Multi-information Display


·

Transmits the ON/OFF signal to the blind spot monitor sensor LH.

·

Transmits a turn signal switch operation signal from the headlight dimmer switch assembly to the blind spot monitor sensor via CAN communication.

·

Displays an error message on the multi-information display if the blind spot monitor detects a malfunction while it is operating.


Main Body ECU (Multiplex Network Body ECU) Sends the destination information and dimmer signal to the blind spot monitor sensor via CAN communication.
Skid Control ECU Transmits a vehicle speed signal to the blind spot monitor sensor via CAN communication.
Hybrid Vehicle Control ECU Assembly Sends a shift position signal (R) and HV flag signal to the blind spot monitor sensor via CAN communication.
Steering Sensor Detects the angle of the steering wheel and sends the resulting signals to the blind spot monitor sensor via CAN communication.


OPERATION DESCRIPTION


a.

Operation description of the blind spot monitor function

i.

Operation conditions

·

The blind spot monitor system is on.

·

Vehicle speed is more than approximately 16 km/h (10 mph).



ii.

Conditions in which a sensor can detect a vehicle

The blind spot monitor function indicates detection of a vehicle in the detection area when either condition is met:

·

When a vehicle is detected in an adjacent lane overtaking this vehicle.

·

When a vehicle is detected entering the detection area because it changed lanes.



iii.
E263938C10
0.063,0.135 0.375,0.292 0.313,0.156 10 false *a 1.083,4.385 1.396,4.542 0.313,0.156 10 false *c 1.938,4.375 2.25,4.531 0.313,0.156 10 false *d 2.688,0.833 3,0.99 0.313,0.156 10 false *b
*a Vehicles in the following areas can be detected:
*b Within approximately 3.5 m (11.49 ft.) from the side of the vehicle
*c Within approximately 3 m (9.85 ft.) behind the rear bumper
*d Within approximately 1 m (3.29 ft.) forward of the rear bumper


Detection area

Vehicles in the following areas can be detected:



b.

Operation description of the RCTA function

i.

Operation conditions:

·

The blind spot monitor system is on.

·

Reverse (R) is selected.

·

The vehicle speed is less than approximately 8 km/h (5 mph).



ii.

Conditions in which a sensor can detect a vehicle

The RCTA function indicates detection of a vehicle in the detection area when both conditions are met:

·

A vehicle is approaching this vehicle from diagonally behind.

·

The vehicle speed is approximately 8 km/h (5 mph) to 28 km/h (17 mph).



iii.
E254389C04
2.604,1.073 2.917,1.271 0.313,0.198 10 false *b 1.104,4.385 1.417,4.583 0.313,0.198 10 false *c 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a
*a Vehicles in the following areas can be detected:
*b Within approximately 5.5 to 20 m (18.04 to 65.62 ft.) from the side of the vehicle (detection area changes according to vehicle speed)
*c Within approximately 6 m (19.69 ft.) behind the rear bumper


Detection area

Vehicles in the following areas can be detected:




OPERATION OF OUTER REAR VIEW MIRROR INDICATOR AND RCTA BUZZER (BLIND SPOT MONITOR BUZZER)


a.

Initial check

i.

When the blind spot monitor system is on with the power switch on (IG), the outer rear view mirror indicator on each outer rear view mirror assembly illuminates for 3 seconds and the RCTA buzzer (blind spot monitor buzzer) sounds for 1 second.


ii.

When the power switch is turned from off to on (IG) with the blind spot monitor system on, the outer rear view mirror indicator on each outer rear view mirror assembly illuminates for 3 seconds.



b.

Operation for each function

i.

Operation for blind spot monitor function

·

When a sensor detects a vehicle in the blind spot area, the outer rear view mirror indicator on the outer rear view mirror assembly illuminates.

·

While the sensor is detecting a vehicle in the detection area and the indicator is illuminated, if the turn signal switch is operated, the outer rear view mirror indicator on the outer rear view mirror assembly starts blinking as shown in the illustration.


E263939C04
5.188,1.104 5.188,0.677 5.188,0.677 6.01,0.677 false 5.667,1.104 5.667,0.677 false 1.208,0.042 3.51,0.365 2.302,0.323 10 false Outer Rear View Mirror Indicator LH: 1.26,1.531 3.802,1.719 2.542,0.188 10 false Outer Rear View Mirror Indicator RH: 4.052,0.083 5.198,0.344 1.146,0.26 10 false Blinking Pattern: 4.135,1.313 4.594,1.51 0.458,0.198 10 false ON 4.073,1.927 4.531,2.125 0.458,0.198 10 false OFF 6.073,0.594 7.042,0.917 0.969,0.323 10 false *a
*a 0.125 seconds - -



ii.

Operation for RCTA function (w/ RCTA)

·

When all of the operation conditions for the RCTA function are met, the outer rear view mirror indicators on the outer rear view mirror assembly blink for 2.5 seconds and the RCTA buzzer (blind spot monitor buzzer) sounds for 2.3 seconds as shown in the illustration.


E254388C09
2.969,0.073 5.229,0.26 2.26,0.188 10 false Outer Rear View Mirror Indicator RH: 0.354,0.073 2.615,0.26 2.26,0.188 10 false Outer Rear View Mirror Indicator LH: 0.146,1.417 3.219,1.604 3.073,0.188 10 false Outer Rear View Mirror Indicator Blinking Pattern: 0.146,3.208 4.927,3.417 4.781,0.208 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) Sounding Pattern: 0.417,2.177 0.729,2.375 0.313,0.198 10 false ON 0.417,3.844 0.729,4.042 0.313,0.198 10 false ON 0.417,2.802 0.729,3 0.313,0.198 10 false OFF 0.417,4.49 0.729,4.688 0.313,0.198 10 false OFF 1.094,1.75 1.333,1.969 0.24,0.219 10 false *a 1.365,1.75 1.604,1.969 0.24,0.219 10 false *a 3.594,2.948 3.833,3.167 0.24,0.219 10 false *b 1.083,3.438 1.323,3.656 0.24,0.219 10 false *c 1.281,3.438 1.521,3.656 0.24,0.219 10 false *c 2.375,3.448 2.615,3.667 0.24,0.219 10 false *d 3.583,4.635 3.854,4.792 0.271,0.156 10 false *e
*a 0.125 seconds *b 2.5 seconds
*c 0.1 seconds *d 0.4 seconds
*e 2.3 seconds - -





RCTA ICON OUTLINE (w/ RCTA)


a.

If a vehicle approaching from the right or left at the rear of the vehicle is detected, the icon will illuminate on the multi-information display.

E338878C01
2.802,1.448 4.885,1.656 4.885,1.656 4.563,1.458 false 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 2.042,0.281 2.354,0.438 0.313,0.156 10 false *b 4.927,1.573 5.24,1.729 0.313,0.156 10 false *c
*a Example *b Multi-information display
*c RCTA Icon - -