Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244875 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E244551E46
3.604,0.698 3.917,0.875 0.313,0.177 10 false BLB 3.427,0.583 3.542,0.76 0.115,0.177 10 false 5 3.604,3.281 3.917,3.458 0.313,0.177 10 false BRB 3.417,3.188 3.531,3.365 0.115,0.177 10 false 5 3.604,4.094 4.042,4.271 0.438,0.177 10 false BRGD 3.344,3.99 3.521,4.167 0.177,0.177 10 false 10 3.354,1.365 3.531,1.542 0.177,0.177 10 false 10 3.604,1.49 4.031,1.646 0.427,0.156 10 false BLGD 1.563,0.854 2.552,1.021 0.99,0.167 10 false ECU-IG1 NO. 4 0.156,0.698 1.146,1.188 0.99,0.49 10 false from IG1-NO. 1 Relay 3.469,4.583 3.906,4.875 0.438,0.292 10 false M56 3.531,2.188 5.146,2.615 1.615,0.427 10 false Blind Spot Monitor Sensor LH 3.469,4.75 5.083,5.094 1.615,0.344 10 false Blind Spot Monitor Sensor RH 0.854,5.313 2.854,5.469 2,0.156 10 false : CAN Communication Line 3.396,2.01 3.802,2.219 0.406,0.208 10 false M55 6.167,1.083 7.156,1.708 0.99,0.625 10 true to CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - AUXILIARY BATTERY)
a.

Disconnect the M55 blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M55-5 (BLB) - Body ground Power switch on (IG) 11 to 14 V
M55-5 (BLB) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M55-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - AUXILIARY BATTERY)
a.

Disconnect the M56 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M56-5 (BRB) - Body ground Power switch on (IG) 11 to 14 V
M56-5 (BRB) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR