Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK HYBRID VEHICLE CONTROL ECU


A364981N03
1.333,0.521 1.75,0.792 0.417,0.271 3.333,0.521 3.75,0.792 0.417,0.271 5.417,0.521 5.833,0.792 0.417,0.271 1.438,0.573 1.813,0.771 0.375,0.198 10 false A50 3.479,0.583 3.833,0.771 0.354,0.188 10 false F2 5.542,0.583 6.104,0.781 0.563,0.198 10 false F3

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A50-7 (STP) - F3-3 (E1) SB - BR Stop light switch assembly signal Brake pedal depressed 11 to 14 V
A50-7 (STP) - F3-3 (E1) SB - BR Stop light switch assembly signal Brake pedal released Below 1 V
F3-52 (VSI1) - F3-51 (E2X1) BR - GR Shift sensor (Main) Power switch on (IG), shift lever in home position or N 2.0 to 3.0 V
F3-52 (VSI1) - F3-51 (E2X1) BR - GR Shift sensor (Main) Power switch on (IG), shift lever in R 0.3 to 1.8 V
F3-52 (VSI1) - F3-51 (E2X1) BR - GR Shift sensor (Main) Power switch on (IG), shift lever in B or D 3.2 to 4.8 V
F3-50 (VSI2) - F3-49 (E2X2) R - BE Shift sensor (Sub) Power switch on (IG), shift lever in home position or N 2.0 to 3.0 V
F3-50 (VSI2) - F3-49 (E2X2) R - BE Shift sensor (Sub) Power switch on (IG), shift lever in R 0.3 to 1.8 V
F3-50 (VSI2) - F3-49 (E2X2) R - BE Shift sensor (Sub) Power switch on (IG), shift lever in B or D 3.2 to 4.8 V
F2-28 (ST1-) - F3-3 (E1) P - BR Stop light switch assembly signal Power switch on (IG), brake pedal depressed Below 1 V
F2-28 (ST1-) - F3-3 (E1) P - BR Stop light switch assembly signal Power switch on (IG), brake pedal released 11 to 14 V
F3-14 (CCS) - F3-3 (E1) BE - BR Cruise control main switch circuit Cruise control main switch (ON/OFF button) not pushed 1 MΩ or higher
F3-14 (CCS) - F3-3 (E1) BE - BR Cruise control main switch circuit Cruise control main switch (ON/OFF button) pushed Below 2.5 Ω
F3-14 (CCS) - F3-3 (E1) BE - BR Cruise control main switch circuit +RES switch ON 235 to 245 Ω
F3-14 (CCS) - F3-3 (E1) BE - BR Cruise control main switch circuit -SET switch ON 617 to 643 Ω
F3-14 (CCS) - F3-3 (E1) BE - BR Cruise control main switch circuit CANCEL switch ON 1509 to 1571 Ω
F3-27 (BATT) - F3-3 (E1) GR - BR Constant power source Always 11 to 14 V


CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781N11
3.396,0.115 3.802,0.354 0.406,0.24 3.49,0.167 4.104,0.365 0.615,0.198 10 false F40

NOTICE:

Do not apply excessive force to the connector. If a force of 10 kg or more is applied, the connector may be broken.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: LHD

*2: RHD

F40-3 (BZ) - F40-28 (GND) P - W-B Skid control buzzer assembly output Power switch on (IG), buzzer not sounding 11 to 14 V
Power switch on (IG), buzzer sounding Below 1 V
F40-7 (B) - F40-28 (GND) P*1 - W-B
B*2 - W-B
Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
F40-8 (CA1P) - F40-28 (GND) LG - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
F40-9 (CA1N) - F40-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
F40-10 (CA2H) - F40-28 (GND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
F40-11 (CA2L) - F40-28 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
F40-23 (SPSW) - F40-28 (GND) GR - W-B Steering pad switch assembly signal (distance control signal) Power switch on (IG), steering pad switch assembly (distance control switch) off 4.75 to 5.25 V
Power switch on (IG), steering pad switch assembly (distance control switch) on Below 1 V
F40-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between F40-8 (CA1P) and F40-28 (GND)

·

Between F40-10 (CA2H) and F40-28 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between F40-9 (CA1N) and F40-28 (GND)

·

Between F40-11 (CA2L) and F40-28 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


E321782N10
2.167,0.75 2.583,1 0.417,0.25 2.292,0.792 2.75,0.99 0.458,0.198 10 false A2

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A2-2 (CA2L) - A2-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A2-3 (CA2H) - A2-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-5 (CA1P) - A2-1 (SGND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-6 (CA1N) - A2-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A2-8 (IGB) - A2-1 (SGND) LG - W-B Power source Power switch on (IG) 11 to 14 V

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between A2-3 (CA2H) and A2-1 (SGND)

·

Between A2-5 (CA1P) and A2-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between A2-2 (CA2L) and A2-1 (SGND)

·

Between A2-6 (CA1N) and A2-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.