Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3210E _58 Vehicle Interior _047531 LIGHTING (INT) _0244928 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Power Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the power switch illumination.

WIRING DIAGRAM

E309266E33
3.302,0.708 3.906,1.031 0.604,0.323 10 false SWIL 3.25,1.333 3.854,1.656 0.604,0.323 10 false AGND 3.74,0.698 4.344,1.021 0.604,0.323 10 false 9 3.74,1.323 4.344,1.646 0.604,0.323 10 false 6 4.813,0.688 5.417,1.01 0.604,0.323 10 false 10 4.813,1.323 5.417,1.646 0.604,0.323 10 false 11 4.708,1.896 5.313,2.219 0.604,0.323 10 false F1 4.698,2.052 6.521,2.615 1.823,0.563 10 false Certification ECU (Smart Key ECU Assembly) 1.427,2.01 2.031,2.333 0.604,0.323 10 false F50 1.417,2.177 2.531,2.604 1.115,0.427 10 false Power Switch 5.896,0.646 6.5,0.969 0.604,0.323 10 false +B 5.063,1.323 5.667,1.646 0.604,0.323 10 false AGND 5.063,0.698 5.667,1.021 0.604,0.323 10 false SWIL

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Power switch illumination ON or OFF -
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Power switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT POWER SWITCH
2.INSPECT POWER SWITCH
a.

b.

Inspect the power switch.

Click hereEngine / Hybrid System>2ZR-FXE STARTING>POWER SWITCH>INSPECTION

OK:

Power switch illumination is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F50-9 (SWIL) - F1-10 (SWIL) Always Below 1 Ω
F50-6 (AGND) - F1-11 (AGND) Always Below 1 Ω
F50-9 (SWIL) or F1-10 (SWIL) - Body ground Always 10 kΩ or higher
F50-6 (AGND) or F1-11 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR