Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1401  Malfunction in Front Speed Sensor RH Circuit  C1402  Malfunction in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1413 and C1414.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1413

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1401 Malfunction in Front Speed Sensor RH Circuit 501
502
507
·

INF Code: 501

·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 502

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 507

·

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Front speed sensor RH

·

Speed sensor installed improperly

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)


ABS DTC
C1402 Malfunction in Front Speed Sensor LH Circuit 511
512
517
·

INF Code: 511

·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 512

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 517

·

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Front speed sensor LH

·

Speed sensor installed improperly

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)


ABS DTC

PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C168336C29
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor
*a OK
*b NG
*c 8.5 N*m
*d No Clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SPEED SENSOR (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR

2.CHECK FRONT SPEED SENSOR (CHECK FOR FOREIGN MATTER)

b.

Check the front speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Install the front speed sensor.


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

c.

Check the speed sensor output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A31 or A15 front speed sensor connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A41-3 (FR+) - A31-1 (FR+) Always Below 1 Ω
A41-3 (FR+) or A31-1 (FR+) - Body ground Always 10 kΩ or higher
A41-4 (FR-) - A31-2 (FR-) Always Below 1 Ω
A41-4 (FR-) or A31-2 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A41-31 (FL+) - A15-1 (FL+) Always Below 1 Ω
A41-31 (FL+) or A15-1 (FL+) - Body ground Always 10 kΩ or higher
A41-32 (FL-) - A15-2 (FL-) Always Below 1 Ω
A41-32 (FL-) or A15-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT SPEED SENSOR ROTOR (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT SPEED SENSOR ROTOR (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor and the component with the speed sensor rotor.

for Speed Sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for Speed Sensor Rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

C

CLEAN FRONT SPEED SENSOR ROTOR