Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1428  Motor Circuit  


DESCRIPTION

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1428 Motor Circuit 611
1160
·

INF Code: 611

·

An open or short in the ABS motor circuit is detected for 2 seconds or more.


·

INF Code: 1160

·

The ABS motor voltage is 18.5 V or more for 0.2 seconds or more.



Brake actuator assembly ABS DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A42 brake actuator assembly connector (for LHD).


d.

Disconnect the A43 brake actuator assembly connector (for RHD).


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A41-40 (+BM) - A42-13 (+BM) Always Below 1 Ω
A41-40 (+BM) or A42-13 (+BM) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A41-40 (+BM) - A43-13 (+BM) Always Below 1 Ω
A41-40 (+BM) or A43-13 (+BM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C346353C09
0.198,0.885 0.563,1.156 0.365,0.271 0.198,0.542 0.563,0.813 0.365,0.271 0.833,1.771 0.813,2.719 true 0.198,0.083 0.51,0.281 0.313,0.198 10 false *a 0.26,0.938 0.573,1.135 0.313,0.198 10 false A43 0.677,2.76 1.271,3 0.594,0.24 10 false MGND 0.25,0.583 0.563,0.781 0.313,0.198 10 false A42 0.625,0.583 0.938,0.781 0.313,0.198 10 false *A 0.625,0.927 0.938,1.125 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A42-1 (MGND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A43-1 (MGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)