Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1434  Steering Angle Sensor Output  


DESCRIPTION

Steering angle sensor signals are input to the skid control ECU (brake booster with master cylinder assembly) via the CAN communication system.

HINT:

When a malfunction occurs in the communication line to the steering angle sensor, U0126 (Lost Communication With Steering Angle Sensor Module) is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTCs may be stored if one of the following occurs:

·

Steering angle sensor zero point malfunction.

·

Steering angle sensor signal malfunction.

·

Steering angle sensor installation abnormality.


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1434 Steering Angle Sensor Output 701 When communication is normal, a steering angle sensor malfunction is detected.
·

Steering angle sensor installed improperly

·

Wire harness or connector

·

Steering angle sensor


VSC DTC

WIRING DIAGRAM

C270521E68
6.042,0.677 6.542,0.875 0.5,0.198 10 false CA1L 6.052,1.271 6.552,1.469 0.5,0.198 10 false CA1H 0.25,4.188 1.833,4.469 1.583,0.281 10 false Steering Angle Sensor 5.052,3.979 5.552,4.177 0.5,0.198 10 false A41 5.781,0.5 6.073,0.729 0.292,0.229 10 false 42 5.781,1.094 6.073,1.323 0.292,0.229 10 false 43 0.813,0.688 1.313,0.885 0.5,0.198 10 false CANL 0.792,1.292 1.292,1.49 0.5,0.198 10 false CANH 1.292,0.5 1.583,0.729 0.292,0.229 10 false 2 1.292,1.094 1.583,1.323 0.292,0.229 10 false 3 0.906,1.979 1.406,2.177 0.5,0.198 10 false BAT 1.292,1.844 1.583,2.073 0.292,0.229 10 false 5 2.063,2.104 3.458,2.313 1.396,0.208 10 false ECU-DCC NO. 1 2.646,1.854 2.938,2.083 0.292,0.229 10 false 1 3.917,1.948 5.313,2.313 1.396,0.365 10 false form Auxiliary Battery 2.188,1.854 2.479,2.083 0.292,0.229 10 false 2 2.094,2.802 3.188,3.01 1.094,0.208 10 false ECU-IG1 NO. 2 2.198,2.531 2.49,2.76 0.292,0.229 10 false 2 2.646,2.531 2.938,2.76 0.292,0.229 10 false 1 3.917,2.615 5.281,2.865 1.365,0.25 10 false form IG1-NO. 1 Relay 0.958,2.656 1.458,2.854 0.5,0.198 10 false IG1 1.302,2.531 1.594,2.76 0.292,0.229 10 false 4 0.906,3.323 1.406,3.521 0.5,0.198 10 false ESS 1.313,3.198 1.604,3.427 0.292,0.229 10 false 1 0.25,4.031 0.75,4.229 0.5,0.198 10 false F55 5.052,4.146 7.115,4.521 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.948,3.563 4.75,3.76 1.802,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG) again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Turn the power switch on (READY).


e.

Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1434 is output. A
CAN communication system DTCs are output. B
Speed sensor and/or yaw rate and acceleration sensor DTCs are output. C


HINT:
·

If there is a malfunction in a speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly), an abnormal value may be output even though the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these malfunctions and inspect the steering angle sensor.





A

2.CHECK STEERING ANGLE SENSOR INSTALLATION

B

C

2.CHECK STEERING ANGLE SENSOR INSTALLATION
a.

Turn the power switch off.


b.

Check that the steering angle sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION

OK:

The steering angle sensor installation is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C269831C18
0.406,1 0.854,1.323 0.448,0.323 2.146,2.604 2.479,2.156 true 0.76,2.083 1.833,2.573 true 0.521,1.063 0.979,1.26 0.458,0.198 10 false F55 2.521,2.042 2.979,2.24 0.458,0.198 10 false BAT 0.521,1.99 0.979,2.188 0.458,0.198 10 false IG1 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Steering Angle Sensor)


Remove the steering wheel and column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the F55 steering angle sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F55-5 (BAT) - Body ground Always 11 to 14 V
F55-4 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C269831C19
0.406,1 0.854,1.323 0.448,0.323 0.76,2.083 1.281,2.583 true 0.521,1.063 0.979,1.26 0.458,0.198 10 false F55 0.458,1.979 0.917,2.177 0.458,0.198 10 false ESS 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering angle sensor, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition
F55-1 (ESS) - Body ground 1 minute after power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)