Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM3210E _59 Vehicle Exterior _047515 WINDOW / GLASS _0244712 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
E292072C21
1.198,1.479 1.906,1.479 false 2.896,1.333 3.208,1.531 0.313,0.198 10 false *c 0.302,2.604 0.615,2.802 0.313,0.198 10 false *a 1,1.396 1.354,1.76 0.354,0.365 10 false *d 2.323,2.24 2.635,2.438 0.313,0.198 10 false *b
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise
*d Motor gear


Connect a positive (+) auxiliary battery lead to connector terminal 2.

NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals 1 and 7 or 10.


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 10.


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 7.


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.



Hide 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
E292071C20
1.563,1.479 2.604,1.479 true 2.646,1.417 2.958,1.615 0.313,0.198 10 false *d 0.26,2.583 0.573,2.781 0.313,0.198 10 false *a 0.531,1.302 0.99,1.5 0.458,0.198 10 false *b 1.115,2.219 1.531,2.531 0.417,0.313 10 false *c
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise
*d Motor gear


Connect a positive (+) auxiliary battery lead to connector terminal 2.

NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals 1 and 7 or 10.


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 10.


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2, connect a negative (-) auxiliary battery lead to terminal 1, and keep them connected for 3 seconds or more.

2.

With terminals 2 and 1 connected, connect a negative (-) auxiliary battery lead to terminal 7.


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.


CAUTION:

Initialize the power window control system after installing the power window regulator motor and regulator assembly.