Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM3210E _59 Vehicle Exterior _047506 MIRROR (EXT) _0244381 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

a.

Check the mirror select and surface adjust switch.

i.
B364151C07
1.76,1 1.76,0.333 1.76,0.333 2.042,0.333 false 0.583,4.229 1.083,3.583 false 1.677,4.24 1.833,3.583 false 1.01,4.24 1.458,3.583 false 1.344,4.24 1.667,3.583 false 1.969,4.229 2.042,3.583 false 2.25,4.24 2.25,3.594 false 2.688,4.229 2.625,3.583 false 0.177,0.156 0.49,0.354 0.313,0.198 10 false *b 2.094,0.219 2.406,0.417 0.313,0.198 10 false *a 2.667,4.26 2.979,4.438 0.313,0.177 10 false B 2.188,4.281 2.5,4.458 0.313,0.177 10 false HL 1.917,4.281 2.229,4.458 0.313,0.177 10 false VL 1.594,4.281 1.844,4.458 0.25,0.177 10 false HR 1.26,4.281 1.51,4.458 0.25,0.177 10 false VR 0.927,4.26 1.177,4.438 0.25,0.177 10 false M+ 0.51,4.25 0.76,4.427 0.25,0.177 10 false E
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
10 (VL) - 7 (B)
13 (M+) - 15 (E)
Up Below 2 Ω
Off 10 kΩ or higher
10 (VL) - 15 (E)
13 (M+) - 7 (B)
Down Below 2 Ω
Off 10 kΩ or higher
9 (HL) - 7 (B)
13 (M+) - 15 (E)
Left Below 2 Ω
Off 10 kΩ or higher
9 (HL) - 15 (E)
13 (M+) - 7 (B)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
12 (VR) - 7 (B)
13 (M+) - 15 (E)
Up Below 2 Ω
Off 10 kΩ or higher
12 (VR) - 15 (E)
13 (M+) - 7 (B)
Down Below 2 Ω
Off 10 kΩ or higher
11 (HR) - 7 (B)
13 (M+) - 15 (E)
Left Below 2 Ω
Off 10 kΩ or higher
11 (HR) - 15 (E)
13 (M+) - 7 (B)
Right Below 2 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

a.

Check the mirror select and surface adjust switch. (for RHD)

i.
B443131C02
1.406,0.969 1.406,0.385 1.406,0.385 1.573,0.385 false 2.167,0.948 2.167,0.365 2.167,0.365 2.333,0.365 false 2.75,3.219 2.917,2.688 false 2.552,3.219 2.469,2.771 false 1,3.219 0.917,2.771 false 0.667,4.083 1,3.583 false 1.083,4.083 1.375,3.583 false 1.417,4.083 1.583,3.583 false 1.75,4.083 1.781,3.583 false 2.083,4.083 2,3.583 false 2.417,4.083 2.167,3.583 false 2.833,4.083 2.583,3.583 false 2.406,0.292 2.719,0.49 0.313,0.198 10 false *b 1.635,0.302 1.948,0.5 0.313,0.198 10 false *c 0.26,0.219 0.573,0.417 0.313,0.198 10 false *a 0.802,2.563 1.115,2.76 0.313,0.198 10 false MR 2.344,2.563 2.656,2.76 0.313,0.198 10 false MAT 2.927,2.542 3.24,2.74 0.313,0.198 10 false E 2.865,4.135 3.177,4.333 0.313,0.198 10 false E 2.406,4.135 2.719,4.333 0.313,0.198 10 false M+ 2.042,4.135 2.354,4.333 0.313,0.198 10 false VR 1.688,4.135 2,4.333 0.313,0.198 10 false HR 1.344,4.135 1.656,4.333 0.313,0.198 10 false VL 0.99,4.135 1.302,4.333 0.313,0.198 10 false HL 0.573,4.125 0.885,4.323 0.313,0.198 10 false B
*a Component without harness connected
(Outer Mirror Switch Assembly)
*b Mirror Retract Switch
*c Mirror Select and Surface Adjust Switch


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
12 (VL) - 15 (B)
9 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
12 (VL) - 7 (E)
Down Below 2 Ω
Off 10 kΩ or higher
13 (HL) - 15 (B)
9 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
13 (HL) - 7 (E)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
10 (VR) - 15 (B)
9 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
10 (VR) - 7 (E)
Down Below 2 Ω
Off 10 kΩ or higher
11 (HR) - 15 (B)
9 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
11 (HR) - 7 (E)
Right Below 2 Ω
Off 10 kΩ or higher



v.

Check the mirror retract switch.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (MAT) - 1 (E) AUTO position Below 35 Ω
Except AUTO position 10 kΩ or higher
4 (MR) - 1 (E) Retract position Below 35 Ω
Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select and surface adjust switch. (for LHD)

i.
B364153C08
2.031,0.979 2.031,0.281 2.031,0.281 2.219,0.281 false 0.5,4.083 1,3.583 false 0.948,4.094 1.396,3.583 false 1.25,4.083 1.583,3.583 false 1.583,4.083 1.771,3.583 false 1.917,4.083 1.979,3.583 false 2.167,4.083 2.167,3.583 false 2.604,4.083 2.563,3.583 false 2.563,3.198 2.583,2.635 false 1,3.208 0.979,2.635 false 0.823,3.219 0.542,2.74 false 1.167,0.938 1.167,0.333 1.167,0.333 1.354,0.333 false 0.271,0.24 0.583,0.396 0.313,0.156 10 false *a 2.375,0.24 2.688,0.396 0.313,0.156 10 false *c 0.792,4.115 1.104,4.271 0.313,0.156 10 false M+ 0.375,4.115 0.688,4.271 0.313,0.156 10 false E 1.115,4.146 1.427,4.302 0.313,0.156 10 false VR 1.5,4.146 1.813,4.302 0.313,0.156 10 false HR 1.833,4.146 2.146,4.302 0.313,0.156 10 false VL 2.104,4.146 2.417,4.302 0.313,0.156 10 false HL 2.604,4.146 2.917,4.302 0.313,0.156 10 false B 2.49,2.469 2.802,2.625 0.313,0.156 10 false MR 0.844,2.458 1.156,2.615 0.313,0.156 10 false MAT 0.427,2.573 0.74,2.729 0.313,0.156 10 false E 1.438,0.25 1.75,0.406 0.313,0.156 10 false *b
*a Component without harness connected
(Outer Mirror Switch Assembly)
*b Mirror Retract Switch
*c Mirror Select and Surface Adjust Switch


Turn the mirror select and surface adjust switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
10 (VL) - 7 (B)
13 (M+) - 15 (E)
Up Below 2 Ω
Off 10 kΩ or higher
10 (VL) - 15 (E)
13 (M+) - 7 (B)
Down Below 2 Ω
Off 10 kΩ or higher
9 (HL) - 7 (B)
13 (M+) - 15 (E)
Left Below 2 Ω
Off 10 kΩ or higher
9 (HL) - 15 (E)
13 (M+) - 7 (B)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select and surface adjust switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
12 (VR) - 7 (B)
13 (M+) - 15 (E)
Up Below 2 Ω
Off 10 kΩ or higher
12 (VR) - 15 (E)
13 (M+) - 7 (B)
Down Below 2 Ω
Off 10 kΩ or higher
11 (HR) - 7 (B)
13 (M+) - 15 (E)
Left Below 2 Ω
Off 10 kΩ or higher
11 (HR) - 15 (E)
13 (M+) - 7 (B)
Right Below 2 Ω
Off 10 kΩ or higher



v.

Check the mirror retract switch.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (MAT) - 5 (E) AUTO position Below 35 Ω
Except AUTO position 10 kΩ or higher
2 (MR) - 5 (E) Retract position Below 35 Ω
Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.