Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C9F11  Hybrid/EV Battery Current Sensor for Driving Control Circuit Short to Ground  P1C9F15  Hybrid/EV Battery Current Sensor for Driving Control Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C9F11 Hybrid/EV Battery Current Sensor for Driving Control Circuit Short to Ground Value of "Hybrid Battery Current for Driving Control" (IBA) is excessively low.
(1 trip detection logic)
Battery voltage sensor Comes on Master Warning Light:
Comes on
P1C9F15 Hybrid/EV Battery Current Sensor for Driving Control Circuit Short to Auxiliary Battery or Open Value of "Hybrid Battery Current for Driving Control" (IBA) is excessively high.
(1 trip detection logic)
Battery voltage sensor Comes on Master Warning Light:
Comes on

IB0 is used for battery control and IBA is used for driving control. Although IB0 and IBA receive voltage output by the battery current sensor through the same terminal, their output may differ as they are connected through separate filter circuits within the battery voltage sensor.

A369460E01
3.573,1.344 3.948,1.823 0.375,0.479 10 false IB 0.875,2.979 2.615,3.344 1.74,0.365 10 false Battery Current Sensor 3.844,3.406 5.521,3.688 1.677,0.281 10 false Battery Voltage Sensor 4.51,1.625 4.885,2.104 0.375,0.479 10 false C1 4.5,2.438 4.875,2.917 0.375,0.479 10 false C2 5.24,1.448 5.615,1.927 0.375,0.479 10 false IB0 5.219,2.24 5.594,2.719 0.375,0.479 10 false IBA 4.896,2.813 6.323,3.26 1.427,0.448 10 false Analogue / Digital 4.885,2.979 6.313,3.427 1.427,0.448 10 false Converter Circuit 5.479,3.417 6.115,3.688 0.635,0.271 10 false C1 < C2

Related Data List
DTC No. Data List
P1C9F11
·

Hybrid Battery Current for Hybrid Battery Control

·

Hybrid Battery Current for Driving Control


P1C9F15

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 10 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check and record any HV system DTCs and freeze frame data.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0AFC00, P0AFC96, P308A12, P0ABF11, P0ABF15, P0ABF28 or P0ABF2A is not output. A
P0AFC00, P0AFC96, P308A12, P0ABF11, P0ABF15, P0ABF28 or P0ABF2A is also output. B



e.

Turn the power switch off.



A

B