DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter, Main Body, Occupant Detection or SRS Airbag / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P-Seatbelt Buckle SW | Front passenger seat belt buckle switch signal | ON or OFF | ON: Front passenger seat belt fastened
OFF: Front passenger seat belt not fastened |
- |
| 2nd-Row Seatbelt Buckle (R) | Rear RH seat belt buckle switch signal | ON or OFF | ON: Rear RH seat belt fastened
OFF: Rear RH seat belt not fastened |
- |
| 2nd-Row Seatbelt Buckle (L) | Rear LH seat belt buckle switch signal | ON or OFF | ON: Rear LH seat belt fastened
OFF: Rear LH seat belt not fastened |
- |
| 2nd-Row Seatbelt Buckle (C) | Rear center seat belt buckle switch signal | ON or OFF | ON: Rear center seat belt fastened
OFF: Rear center seat belt not fastened |
- |
| Driver Side Seatbelt Warning Buzzer | Driver seat belt warning buzzer | ON or OFF | Customize setting displayed | - |
| P-Seatbelt Warning Buzzer | Front passenger seat belt warning buzzer | ON or OFF | Customize setting displayed | - |
| Rear Seatbelt Warning Buzzer | Rear seat belt warning buzzer | ON or OFF | Customize setting displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Buckle SW | Front passenger buckle switch | Unset, Set or NG | Unset: Seat belt not fastened
Set: Seat belt fastened NG: Data is not determined |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Left side Buckle SW | LH buckle switch | Unset, Set or NG | Unset: Seat belt not fastened
Set: Seat belt fastened NG: Data is not determined |
- |
| Right side Buckle SW | RH buckle switch | Unset, Set or NG | Unset: Seat belt not fastened
Set: Seat belt fastened NG: Data is not determined |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door Courtesy SW | Rear door courtesy light switch RH | ON or OFF | ON: Rear door RH open
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door courtesy light switch LH | ON or OFF | ON: Rear door LH open
OFF: Rear door LH closed |
- |
| D Seat Buckle SW | Driver seat belt buckle switch | ON or OFF | ON: Driver seat belt unfastened
OFF: Driver seat belt fastened |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Front seat belt warning light | ON or OFF | - |
| Rear Seat Belt | Rear seat belt warning light | ON or OFF | - |