Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3210E _56 Audio / Visual / Telematics _057161 TELEMATICS _0287335 TELEMATICS SYSTEM D

TELEMATICS  TELEMATICS SYSTEM  OPERATION CHECK  


ENTER TEST MODE


HINT:
·

By performing a test call, it is possible to check the operation of the telematics transceiver.

·

Make sure to perform a test call after troubleshooting the telematics system.

·

Depending on radio wave signal conditions and the test center condition, a test call may fail even though the vehicle is not malfunctioning.



a.

Enter test mode by using either of the following methods:


b.

Method 1 (Recommended)

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG)


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Telematics / Utility / Emergency Call Check

Body Electrical > Telematics > Utility
Tester Display
Emergency Call Check
50005 233 4415

v.

According to the display on the GTS, perform Emergency Call Check to enter test mode.



c.

Method 2

i.

Turn the taillights on and off at an interval of 10 seconds or less as follows:

for Light Control Switch with Off Position:

Operate the light control switch as follows: Off → Tail → Off → Tail → Off → Tail → Off → Tail → Off → Tail →Off → Tail → Off → Tail → Off → Tail → Off → Tail → Off → Tail.


for Light Control Switch without Off Position:

Expose the automatic light control sensor to a light and then operate the light control switch as follows: AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail →AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail → AUTO → Tail.


for Light Control Switch without Off Position (if the above procedure cannot be completed successfully):

Turn the light control switch to the AUTO position, expose the automatic light control sensor to a light and then cover and uncover the light control sensor to turn the taillights on and off as follows: Off → On → Off → On → Off → On → Off → On → Off → On →Off → On → Off → On → Off → On → Off → On → Off → On.



ii.
E338332C01
1.094,1.927 1.344,1.927 1.344,1.927 1.344,1.51 false 2.354,1.927 2.104,1.927 2.104,1.927 2.104,1.51 false 0.875,1.833 1.115,2.063 0.24,0.229 10 false *a 2.417,1.844 2.656,2.073 0.24,0.229 10 false *b
*a Manual (SOS) Switch Green Indicator
*b Manual (SOS) Switch Red Indicator


Check that the manual (SOS) switch indicators begin blinks 5 times over 10 seconds and then turn off. Push the manual (SOS) switch for less than 3 seconds within 15 seconds after the indicators begin to blink to enter test mode.




PERFORM TEST CALL


a.

Enter test mode.

HINT:

The manual (SOS) switch indicator (green) will blink 3 times to indicate that test mode has been entered.



b.

Speak into the telephone microphone assembly and confirm that your voice can be heard from the speakers, and then press the manual (SOS) switch for 3 seconds or less to enter test call mode.

HINT:
·

If your voice cannot be heard from the speakers, press and hold the manual (SOS) switch for 3 to 10 seconds.

·

The manual (SOS) switch indicator (green) will blink 4 times.




c.

Press the manual (SOS) switch and check that the manual (SOS) switch indicator (green) blinks 1 time. A test call will be performed and test data will be transmitted.

HINT:
·

The manual (SOS) switch indicator (green) will illuminate for 10 seconds if test data transmission was successful.

·

The manual (SOS) switch indicator (red) will illuminate for 10 seconds if test data transmission fails.





DCM Operation History


HINT:

This function is used to display operation history information and the time at which it was stored in the telematics transceiver.


a.

Check DCM Operation History

HINT:

When problem symptoms due to wave interference cannot be reproduced, this function provides telematics transceiver operation history information which can be used to explain the cause of the malfunction to the customer.


i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Telematics / Utility / DCM Operation History

Body Electrical > Telematics > Utility
Tester Display
DCM Operation History
50005 233 42
Item Function Parameter Name
Operation History Displays the result of an attempt emergency call. Success
Fail
Activation Failed Displays the reason for failure if communication failed. Unrecognized VIN
Unrecognized DCM-ID
Unrecognized IMSI
Unavailable Service Center
Service Already Activated
Backup Battery Status Displays the mobilephone battery condition. Low Battery Amount
Low Battery Voltage
Battery Exhaustion
Abnormal