2005-2008 RAV4 · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007


1. INSTALL CHECK VALVE GROMMET
  1. Install the check valve grommet to the brake booster assembly.


2. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY
  1. Install the brake vacuum check valve assembly to the brake booster assembly.


3. INSTALL BRAKE BOOSTER GASKET
  1. Install a new brake booster gasket to the brake booster assembly.


4. INSTALL BRAKE BOOSTER ASSEMBLY

  1. C174093E01
    Tape the tip of the push rod of the brake booster assembly.

  1. Install the brake booster assembly to the body by pushing the push rod as shown in the illustration.

    NOTICE:
    Do not damage the brake lines or clamps. If any parts are damaged, replace them with new ones.

  1. C170034
    Engage the 3 clamps with the brake lines.


5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

    HINT:
    Fully tighten the lock nut after adjusting the brake pedal height.

  1. C128760
    Completely install the brake booster assembly with the 4 nuts.

    Torque:
    12.7 N*m{ 130 kgf*cm , 9 ft.*lbf }


6. INSTALL NO. 1 HOSE TO HOSE TUBE

  1. C170036
    Install the No. 1 hose to hose tube with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Slide the 2 clips and connect the No. 1 hose to hose tube.


7. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:
  1. The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure to tip of the master cylinder points downward when handling the master cylinder.
  2. Make sure foreign matter does not attach to the master cylinder's piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.

  1. Install a new O-ring to the master cylinder.

  1. C127056
    Install the master cylinder to the booster with the 2 nuts.

    Torque:
    12.5 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. C127055E01
    Using SST, connect the 2 brake lines labeled C to the master cylinder.
    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 144 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. Connect the brake fluid level warning switch connector labeled B to the master cylinder.

  1. for Manual Transaxle:
    Connect the clutch reservoir tube labeled A to the master cylinder.


8. INSTALL COWL BODY MOUNTING REINFORCEMENT RH

  1. C170048
    Install the cowl body mounting reinforcement RH with the 2 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


9. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY

  1. C170035
    Install the cowl top panel outer sub-assembly with the 14 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    Torque:
    7.5 N*m{ 76 kgf*cm }

  1. Connect the connector.


10. INSTALL COWL VENTILATOR HOUSING SUB-ASSEMBLY

  1. C170049
    Engage the 4 clips to install the cowl ventilator housing sub-assembly.


11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

B133583
  1. Connect the connector and attach the clamp.

  1. Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body, and install the wiper motor and link.

  1. Install the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


12. INSTALL COWL TOP VENTILATOR LOUVER

B131453
  1. Attach the 12 claws and install the louver.

  1. Install the 2 clips.


13. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

E125248E01
  1. Attach the claw to install the front fender to cowl side seal.


14. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

B133588
  1. Attach the claw to install the front fender to cowl side seal.


15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E07
    Stop the wiper motor at the automatic stop position.

  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.

  1. B133593E01
    Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    Hold down the arm hinge with your hand while tightening the nut.


16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E07
    Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.

  1. B133594E01
    Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    Hold down the arm hinge with your hand while tightening the nut.

  1. Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.


17. INSTALL WINDSHIELD WIPER ARM COVER
  1. Install the 2 caps.


18. INSTALL PUSH ROD PIN

C130666E05

C130668E03
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Install the push rod pin to the push rod clevis.

    NOTICE:
    The push rod pin must be installed as shown in the illustration.

  1. Install the clip to the push rod pin.

    NOTICE:
    The clip must be installed as shown in the illustration.


19. FILL RESERVOIR WITH BRAKE FLUID

  1. C126432
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    NOTICE:
    1. Make sure there is sufficient brake fluid in the can.
    2. After adding braking fluid, make sure the reservoir is sufficiently full.


20. BLEED BRAKE MASTER CYLINDER

C126433

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.

  1. C126434
    Block the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 144 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


21. BLEED BRAKE LINE

C126435E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.


22. BLEED ABS AND TRACTION ACTUATOR

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. B127990E01
    Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the suction line.

    NOTICE:
    1. Perform the bleeding at the right front wheel and right rear wheel.
    2. Bleed the air by following the steps displayed on the intelligent tester.


    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.

    2. Loosen the bleeder plug.

    3. Operate the brake actuator to bleed the air using the intelligent tester.

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    4. Check if the operation has stopped by referring to the intelligent tester display.

    5. Temporarily tighten the bleeder plug.

    6. Repeat the 4 previous steps until all air in the fluid is completely bled out.

    7. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    8. Repeat all of the above procedures for the right rear wheel to bleed the air out of the suction line.

  1. Bleed the air out of the pressure reduction line.

    NOTICE:
    1. Perform the bleeding at the 4 wheels.
    2. Bleed the air by following the steps displayed on the intelligent tester.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug.

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.

    4. Tighten the bleeder plug, then release the brake pedal.

    5. Repeat the 3 previous steps until all air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.


23. INSPECT BRAKE FLUID LEVEL IN RESERVOIR

C126431
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.


24. INSPECT FOR FLUID LEAK
← REMOVAL (from Aug 2007)COMPONENTS (from Aug 2007) →