Install a new gasket and O-ring to the timing chain cover as shown in the illustration.
Apply seal packing in a continuous bead to the timing chain cover as shown in the illustration.
Seal packing:
Toyota genuine seal packing black, three bond 1207B or equivalent
Standard seal diameter:
Position
Specified Condition
A - A
2.0 to 4.0 mm (0.079 to 0.157 in.)
B - B
8.0 to 10.0 mm (0.315 to 0.394 in.)
C - C
Width: 13 mm (0.512 in.) Height: 6mm (0.236 in.)
NOTICE:
Be sure to clean and degrease the contact surfaces, especially 4 areas indicated by the arrows in the illustration.
When the contact surfaces are wet, wipe them off with an oil-free cloth before applying seal packing.
When applying seal packing to area C - C, apply it in the direction of the white arrows in the illustration.
Install the crankcase within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Do not start the engine for at least 4 hours after installing.
Apply adhesive to the 4 bolts.
Adhesive:
Toyota genuine adhesive 1324, three bond 1324 or equivalent
HINT:
Bolt length: 37.5 mm (1.476 in.)
Temporarily install the timing chain cover with the 4 bolts.
Temporarily install a new seal washer and bolt A.
HINT:
Bolt length: 67.5 mm (2.657 in.)
Temporarily install the 8 bolts.
HINT:
Bolt length: 37.5 mm (1.476 in.)
Using several steps, install the 13 bolts.
Torque:
31.5 N*m{
321 kgf*cm
, 23 ft.*lbf
}
for except bolt A
21 N*m{
214 kgf*cm
, 15 ft.*lbf
}
for bolt A
Using a 10 mm socket hexagon wrench, install a new gasket and the timing chain cover tight plug.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
2.
INSTALL WATER PUMP
Install a new gasket onto the timing chain cover as shown in the illustration.
Clean the 7 bolts and 7 bolt holes.
Temporarily install the water pump.
Standard bolt length:
Item
Specified Condition
Bolt A and C
45 mm (1.77 in.)
Bolt B
30 mm (1.18 in.)
Apply adhesive to 2 or 3 threads of the bolt labeled A.
Adhesive:
Toyota genuine adhesive 1324, three bond 1324 or equivalent.
Temporarily install the water pump with the 7 bolts.
Tighten the 2 bolts indicated by the arrows in the illustration. Then tighten the other bolts.
Torque:
32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
3.
INSTALL CRANKSHAFT PULLEY
Align the keyway of the pulley with the key located on the crankshaft, then slide the pulley into place.
Using SST, install the pulley bolt.
SST
09213-58013 09330-00021
Torque:
250 N*m{
2,550 kgf*cm
, 184 ft.*lbf
}
4.
INSTALL OIL STRAINER
Install a new O-ring and the oil strainer with the 3 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
5.
INSTALL OIL FILTER BRACKET
Install a new gasket and the oil filter bracket with the 4 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
6.
INSTALL OIL FILTER ELEMENT
Clean the oil filter cap threads and O-ring groove.
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
Set a new oil filter element in the oil filter cap.
7.
INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
Apply seal packing in a continuous bead as shown in the illustration.
Seal packing:
Toyota genuine seal packing black, three bond 1207B or equivalent
Standard seal diameter:
4.0 to 7.0 mm (0.157 to 0.276 in.)
NOTICE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Do not start the engine for at least 4 hours after installing.
Install the oil pan with the 18 bolts and 2 nuts.
Torque:
10.5 N*m{
107 kgf*cm
, 8 ft.*lbf
}
Install a new gasket and the drain plug.
Torque:
38 N*m{
387 kgf*cm
, 28 ft.*lbf
}
8.
INSTALL OIL FILTER CAP
Remove any dirt or foreign matter from the installation surface and inside of the engine.
Apply a small amount of engine oil to the O-ring again and install the oil filter cap.
NOTICE:
Be careful that the O-ring does not get caught between the parts.
Using SST, tighten the oil filter cap.
SST
09228-06501
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
NOTICE:
Make sure that the oil filter is installed securely as shown in the illustration.
Be careful that the O-ring does not get caught between the parts.
Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
NOTICE:
Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.
Install the oil filter drain plug to the filter cap.
Torque:
12.5 N*m{
127.5 kgf*cm
, 9.2 ft.*lbf
}
NOTICE:
Be careful that the O-ring does not get caught between the parts.
Close the oil filter element service cover and install the clip.
9.
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Clean the contact surface of the cylinder head cover, cylinder head and timing chain cover.
Fit a new cylinder head cover gasket and a new No. 2 gasket into the gasket groove on the cover.
Apply a continuous bead of seal packing (diameter: 8 mm (0.31 in.) to the contact surface between the cylinder head assembly and cylinder head cover assembly as shown in the illustration.
Seal packing:
Toyota genuine seal packing block, three bond 1207B or equivalent
Standard seal diameter:
8 mm (0.31 in.)
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes after applying seal packing.
Do not apply engine oil for at least 2 hours after installing.
Install the gasket to the cylinder head cover.
Install the cylinder head cover with the 13 bolts, 4 nozzle holder clamp seats, 2 nuts and 2 washers. Uniformly tighten the bolts and nuts in several passes.
Torque:
16 N*m{
163 kgf*cm
, 12 ft.*lbf
}
for bolt A (Nozzle holder clamp seat)11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
for other bolts