2005-2008 RAV4 · Service Manual BRAKE

TERMINALS OF ECU

System information · Vehicles built from Nov 2005


SKID CONTROL ECU
C110609E02
Symbols (Terminal No.)
Terminal Description
+BS (A27-1)
Solenoid valve power supply
GND1 (A27-2)
Skid control ECU ground
CANL (A27-5)
CAN communication line L
CANH (A27-6)
CAN communication line H
FL- (A27-8)
Front LH wheel speed signal input
FL+ (A27-9)
Front LH wheel speed sensor power supply
STP (A27-10)
Stop light switch input
RL+ (A27-11)
Rear LH wheel speed sensor power supply
RL- (A27-12)
Rear LH wheel speed signal input
+BM (A27-23)
Motor relay power supply
GND2 (A27-24)
Actuator pump motor ground
IG1 (A27-25)
ECU power supply
SP1 (A27-26)
Speed signal output for speedometer
FR- (A27-30)
Front RH wheel speed signal input
FR+ (A27-31)
Front RH wheel speed sensor power supply
RR+ (A27-33)
Rear RH wheel speed sensor power supply
RR- (A27-34)
Rear RH wheel speed signal input
VGS (A27-28)
Deceleration sensor power supply
GL1 (A27-4)
Deceleration sensor signal input
GGND (A27-7)
Deceleration sensor ground
TS (A27-15)
Sensor diagnosis check input

CHECK SKID CONTROL ECU
C107496E02
  1. Disconnect the A27 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +BS (A27-1) - Body ground
    W - Body ground
    Solenoid valve power supply
    Always
    10 to 14 V
    GND1 (A27-2) - Body ground
    W-B - Body ground
    Skid control ECU ground
    Always
    Below 1 Ω
    STP (A27-10) - Body ground
    L - Body ground
    Stop light switch input
    Stop light switch ON
    Brake pedal depressed
    8 to 14 V
    STP (A27-10) - Body ground
    L - Body ground
    Stop light switch input
    Stop light switch OFF
    Brake pedal released
    Below 1.5 V
    +BM (A27-23) - Body ground
    B - Body ground
    Motor relay power supply
    Always
    10 to 14 V
    GND2 (A27-24) - Body ground
    W-B - Body ground
    Actuator pump motor ground
    Always
    Below 1 Ω
    IG1 (A27-25) - Body ground
    L - Body ground
    ECU power supply
    Ignition switch on (IG)
    10 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
C126316E01
  1. Disconnect the ID junction block connector.

  2. Measure the resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch ON
    Below 1 Ω
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch OFF
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ID junction block connector.

  4. Measure the voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch ON
    Below 1 V
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch OFF
    10 to 14 V
    If the result is not as specified, there may be a malfunction in the junction block (ECU).

← PROBLEM SYMPTOMS TABLE (from Aug 2008)DIAGNOSIS SYSTEM (Nov 2005 – Dec 2006) →