Symbols (Terminal No.)
|
Wiring Colors
|
Terminal Descriptions
|
Conditions
|
Specified Conditions
|
BATT (A12-20) - E1 (B32-104)
|
W - BR
|
Battery (for measuring battery voltage and for ECM memory)
|
Always
|
9 to 14 V
|
+B (A12-2) - E1 (B32-104)
|
B - BR
|
Power source of ECM
|
Ignition switch on (IG)
|
9 to 14 V
|
+B2 (A12-1) - E1 (B32-104)
|
B - BR
|
Power source of ECM
|
Ignition switch on (IG)
|
9 to 14 V
|
+BM (A12-3) - E1 (B32-104)
|
LG - BR
|
Power source of throttle actuator
|
Always
|
9 to 14 V
|
IGT1 (B32-85) - E1 (B32-104) IGT2 (B32-84) - E1 (B32-104) IGT3 (B32-83) - E1 (B32-104) IGT4 (B32-82) - E1 (B32-104)
|
R - BR P - BR G - BR L - BR
|
Ignition coil (ignition signal)
|
Idling
|
Pulse generation (see waveform 1)
|
IGF1 (B32-81) - E1 (B32-104)
|
W - BR
|
Ignition coil (ignition confirmation signal)
|
Ignition switch on (IG)
|
4.5 to 5.5 V
|
Idling
|
Pulse generation (see waveform 1)
|
NE+ (B32-122) - NE- (B32-121)
|
W - B
|
Crankshaft position sensor
|
Idling
|
Pulse generation (see waveform 2)
|
G2+ (B32-99) - G2- (B32-98)
|
L - Y
|
Camshaft position sensor
|
Idling
|
Pulse generation (see waveform 2)
|
#10 (B32-108) - E1 (B32-104) #20 (B32-107) - E1 (B32-104) #30 (B32-106) - E1 (B32-104) #40 (B32-105) - E1 (B32-104)
|
L - BR G - BR B - BR W - BR
|
Injector
|
Ignition switch on (IG)
|
9 to 14 V
|
Idling
|
Pulse generation (see waveform 3)
|
HA1A (B32-109) - E04 (B32-46)
|
L - W-B
|
A/F sensor heater
|
Ignition switch on (IG)
|
9 to 14 V
|
Idling
|
Below 3.0 V
|
A1A+ (B32-112) - E1 (B32-104)
|
G - BR
|
A/F sensor
|
Idling
|
Below 3.3 V*1
|
A1A- (B32-113) - E1 (B32-104)
|
R - BR
|
A/F sensor
|
Idling
|
Below 3.0 V*1
|
HT1B (B32-47) - E03 (B32-86)
|
R - W-B
|
Heated oxygen sensor heater
|
Ignition switch on (IG)
|
9 to 14 V
|
Idling
|
Below 3.0 V
|
OX1B (B32-64) - EX1B (B32-87)
|
B - BR
|
Heated oxygen sensor
|
Engine speed maintained at 2,500 rpm for 2 minutes after warming up sensor
|
Pulse generation (see waveform 4)
|
KNK1 (B32-110) - EKNK (B32-111)
|
B - W
|
Knock sensor
|
Engine speed maintained at 4,000 after warming up engine
|
Pulse generation (see waveform 5)
|
SPD (A12-8) - E1 (B32-104)
|
V - BR
|
Speed signal from combination meter
|
Driving at 20 km/h (12 mph)
|
Pulse generation (see waveform 6)
|
THW (B32-97) - ETHW (B32-96)
|
GR - BR
|
Engine coolant temperature sensor
|
Idling, Engine coolant temperature 80°C (176°F)
|
0.2 to 1.0 V
|
THA (B32-65) - ETHA (B32-88)
|
W - BR
|
Intake air temperature sensor
|
Idling, Intake air temperature 20°C (68°F)
|
0.5 to 3.4 V
|
VG (B32-118) - E2G (B32-116)
|
R - LG
|
Mass air flow meter
|
Idling, Shift lever position P or N, A/C switch OFF
|
0.5 to 3.0 V
|
W (A12-24) - E1 (B32-104)
|
R - BR
|
MIL
|
Ignition switch on (IG) (MIL goes off)
|
Below 3.0 V
|
Idling
|
9 to 14 V
|
STA (A12-48) - E1 (B32-104)
|
LG - BR
|
Starter signal
|
Cranking
|
5.5 V or more
|
VTA1 (B32-115) - ETA (B32-91)
|
G - BR
|
Throttle position sensor (for engine control)
|
Ignition switch on (IG), Throttle valve fully closed
|
0.5 to 1.2 V
|
Ignition switch on (IG), Throttle valve fully open
|
3.2 to 4.8 V
|
VTA2 (B32-114) - ETA (B32-91)
|
L - BR
|
Throttle position sensor (for sensor malfunction detection)
|
Ignition switch on (IG), Accelerator pedal released
|
2.1 to 3.1 V
|
Ignition switch on (IG), Accelerator pedal depressed
|
4.5 to 5.5 V
|
VCTA (B32-67) - ETA (B32-91)
|
Y - BR
|
Power source of sensor (specific voltage)
|
Ignition switch on (IG)
|
4.5 to 5.5 V
|
VCPA (A12-57) - EPA (A12-59)
|
B - Y
|
Power source of accelerator pedal position sensor (for VPA)
|
Ignition switch on (IG)
|
4.5 to 5.5 V
|
VPA (A12-55) - EPA (A12-59)
|
W - Y
|
Accelerator pedal position sensor (for engine control)
|
Ignition switch on (IG), Accelerator pedal released
|
0.5 to 1.1 V
|
Ignition switch on (IG), Accelerator pedal fully depressed
|
2.6 to 4.5 V
|
VPA2 (A12-56) - EPA2 (A12-60)
|
R - O
|
Accelerator pedal position sensor (for sensor malfunctioning detection)
|
Ignition switch on (IG), Accelerator pedal released
|
1.2 to 2.0 V
|
Ignition switch on (IG), Accelerator pedal fully depressed
|
3.4 to 5.0 V
|
VCP2 (A12-58) - EPA2 (A12-60)
|
L - O
|
Power source of accelerator pedal position sensor (for VPA2)
|
Ignition switch on (IG)
|
4.5 to 5.0 V
|
M+ (B32-42) - ME01 (B32-43)
|
B - W-B
|
Throttle actuator
|
Idling with warm engine
|
Pulse generation (see waveform 7)
|
M- (B32-41) - ME01 (B32-43)
|
W - W-B
|
Throttle actuator
|
Idling with warm engine
|
Pulse generation (see waveform 8)
|
STP (A12-36) - E1 (B32-104)
|
L - BR
|
Stop light switch
|
Brake pedal depressed
|
9 to 14 V
|
Brake pedal released
|
Below 1.5 V
|
ST1- (A12-35) - E1 (B32-104)
|
GR - BR
|
Stop light switch
|
Ignition switch on (IG), Brake pedal depressed
|
Below 1.5 V
|
Ignition switch on (IG), Brake pedal released
|
9 to 14 V
|
PRG (B32-49) - E1 (B32-104)
|
G - BR
|
Purge VSV
|
Ignition switch on (IG)
|
9 to 14 V
|
Idling
|
Pulse generation (see waveform 9)
|
FC (A12-7) - E1 (B32-104)
|
W - BR
|
Fuel pump control
|
Ignition switch on (IG)
|
9 to 14 V
|
Idling
|
Below 1.5 V
|
TACH (A12-15) - E1 (B32-104)
|
GR - BR
|
Engine speed
|
Idling
|
Pulse generation (see waveform 10)
|
TC (A12-27) - E1 (B32-104)
|
G - BR
|
Terminal TC of DLC3
|
Ignition switch on (IG)
|
9 to 14 V
|
OC1+ (B32-100) - OC1- (B32-123)
|
BR - L
|
Camshaft timing oil control valve (OCV)
|
Idling
|
Pulse generation (see waveform 11)
|
CANH (A12-41) - E1 (B32-104)
|
Y - BR
|
CAN communication line
|
Ignition switch on (IG)
|
Pulse generation (see waveform 12)
|
CANL (A12-49) - E1 (B32-104)
|
W - BR
|
CAN communication line
|
Ignition switch on (IG)
|
Pulse generation (see waveform 13)
|
ELS1 (A12-31) - E1 (B32-104)
|
O - BR
|
Electric load
|
Taillight switch on
|
7.5 to 14 V
|
Taillight switch off
|
Below 1.5 V
|
ELS3 (A12-33) - E1 (B32-104)
|
G - BR
|
Electric load
|
Defogger switch on
|
7.5 to 14 V
|
Defogger switch off
|
Below 1.5 V
|
FANL (A12-21) - E1 (B32-104)
|
R - BR
|
FAN NO. 3 relay
|
Ignition switch on (IG)
|
9 to 14 V
|
Idling with A/C ON or High engine coolant temperature
|
Below 1.5 V
|
FANH (A12-22) - E1 (B32-104)
|
W - BR
|
FAN NO. 1, 2 relay
|
Idling with high engine coolant temperature
|
Below 1.5 V
|
ALT (B32-50) - E1 (B32-104)
|
B - BR
|
Generator
|
Ignition switch on (IG)
|
9 to 14 V
|
IGSW (A12-28) - E1 (B32-104)
|
B - BR
|
Ignition switch
|
Ignition switch on (IG)
|
9 to 14 V
|
MREL (A12-44) - E1 (B32-104)
|
O - BR
|
EFI MAIN relay
|
Ignition switch on (IG)
|
9 to 14 V
|
ACCR (A12-13)*2 - E1 (B32-104)
|
LG - BR
|
Accessory power cut signal
|
Ignition switch on (IG) → Cranking
|
Below 1.5 V
|
STSW (A12-14)*2 - E1 (B32-104)
|
R - BR
|
Engine cranking required signal
|
Ignition switch on (IG) → Cranking
|
Below 1 V → 9 to 14 V momentary
|
STAR (B32-52) - E1 (B32-104)
|
W - BR
|
ST relay control
|
Cranking
|
9 to 14 V
|
VCIB (B32-69) - EIB (B32-92)
|
R - BR
|
Battery current sensor
|
Ignition switch on (IG)
|
4.5 to 5.0 V
|
IB (B32-68) - EIB (B32-92)
|
B - BR
|
Battery current sensor
|
Ignition switch on (IG)
|
0.5 to 4.5 V
|
THB (B32-120) - EIB (B32-92)
|
LB - BR
|
Battery temperature sensor
|
Ignition switch on (IG)
|
0.5 to 4.5 V
|