P0115 Engine Coolant Temperature Circuit Malfunction
Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006
Also covers:
- P0117 Engine Coolant Temperature Circuit Low Input
- P0118 Engine Coolant Temperature Circuit High Input
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
A thermistor, whose resistance value varies according to the ECT, is built into the Engine Coolant Temperature (ECT) sensor.The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.
- HINT:
- When any of DTCs P0115, P0117 and P0118 are set, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
| DTC No. |
Proceed to |
DTC Detection Condition |
Trouble Area |
| P0115 |
Step 1 |
Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117 |
Step 4 |
Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0118 |
Step 2 |
Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic) |
|
- HINT:
- When any of these DTCs are set, check the ECT by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Temperature Displayed |
Malfunction |
| -40°C (-40°F) |
Open circuit |
| 140°C (284°F) or higher |
Short circuit |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
- Standard:
- Between 80°C and 100°C (176°F and 212°F) with warm engine.
- Result:
Temperature Displayed
Proceed to
-40°C (-40°F)
A
140°C (284°F) or higher
B
Between 80°C and 100°C (176°F and 212°F)
C
- HINT:
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the B4 Engine Coolant Temperature (ECT) sensor connector.

Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
- Standard:
- 140°C (284°F) or higher.
Reconnect the ECT sensor connector.
|
|
||||
| NG | |
| 3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the B4 ECT sensor connector.

Disconnect the B32 ECM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
THW (B4-2) - THW (B32-97)
Below 1 Ω
E2 (B4-1) - ETHW (B32-96)
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
Disconnect the B4 ECT sensor connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value displayed on the tester.
- Standard:
- -40°C (-40°F)
Reconnect the ECT sensor connector.
|
|
||||
| NG | |
| 5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the B4 ECT sensor connector.

Disconnect the B32 ECM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
THW (B4-2) or THW (B32-97) - Body ground
10 kΩ or higher
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
