P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Also covers:
- P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
- P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
- P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit
- P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input
- P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input
- P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
CAUTION / NOTICE / HINT
- HINT:
- These DTCs relate to the Throttle Position (TP) sensor.
DESCRIPTION
The Throttle Position (TP) sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions such as at high speeds and very low speeds.The TP sensor has two sensor circuits which each transmit a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0120 |
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0122 |
Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0123 |
Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0220 |
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0222 |
Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0223 |
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P2135 |
Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more |
|
- HINT:
- When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position and Throttle Position No.2.
- When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position and Throttle Position No.2.
- Throttle Position denotes the VTA1 signal, and Throttle Position No.2 denotes the VTA2 signal.
- Reference (Normal Condition):
Tester Display
Accelerator Pedal Fully Released
Accelerator Pedal Fully Depressed
Throttle Position
0.5 to 1.1 V
3.3 to 4.9 V
Throttle Position No.2
2.1 to 3.1 V
4.6 to 5.0 V
- Throttle Position denotes the VTA1 signal, and Throttle Position No.2 denotes the VTA2 signal.
FAIL-SAFE
When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION AND THROTTLE POSITION NO.2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position and Throttle Position No.2.
Read the values displayed on the tester.
- Result:
TP (VTA1)
When Accelerator pedal Released
TP No.2 (VTA2)
When Accelerator pedal Released
TP (VTA1)
When Accelerator pedal Depressed
TP No.2 (VTA2)
When Accelerator pedal Depressed
Trouble Area
Proceed to
0 V to 0.2 V
0 V to 0.2 V
0 V to 0.2 V
0 V to 0.2 V
VC circuit open
A
4.5 V to 5.0 V
4.5 V to 5.0 V
4.5 V to 5.0 V
4.5 V to 5.0 V
E2 circuit open
0 V to 0.2 V,
or 4.5 V to 5.0 V
2.4 V to 3.4 V
(Fail-safe)
0 V to 0.2 V,
or 4.5 V to 5.0 V
2.4 V to 3.4 V
(Fail-safe)
VTA1 circuit open or ground short
0.7 V to 1.3 V
(Fail-safe)
0 V to 0.2 V,
or 4.5 V to 5.0 V
0.7 V to 1.3 V
(Fail-safe)
0 V to 0.2 V,
or 4.5 V to 5.0 V
VTA2 circuit open or ground short
0.5 V to 1.1 V
2.1 V to 3.1 V
3.3 V to 4.9 V
(Not fail-safe)
4.6 V to 5.0 V
(Not fail-safe)
TP sensor circuit normal
B
- HINT:
- TP denotes Throttle Position , and TP No.2 denotes Throttle Position No.2.
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the B3 throttle body connector.
Disconnect the B32 ECM connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
VC (B3-5) - VCTA (B32-67)
Below 1 Ω
VTA (B3-6) - VTA1 (B32-115)
VTA2 (B3-4) - VTA2 (B32-114)
E2 (B3-3) - ETA (B32-91)
- Standard resistance (Check for short):
Tester Connection
Specified Condition
VC (B3-5) or VCTA (B32-67) - Body ground
10 kΩ or higher
VTA (B3-6) or VTA1 (B32-115) - Body ground
VTA2 (B3-4) or VTA2 (B32-114) - Body ground
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. INSPECT ECM (VC VOLTAGE) |
![]() ![]() |
Disconnect the B3 throttle body connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals of the throttle body connector.
- Standard voltage:
Tester Connection
Specified Condition
VC (B3-5) - E2 (B3-3)
4.5 to 5.5 V
Reconnect the throttle body connector.
|
|
||||
| OK | |
| 4. REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135
A
No output
B
|
|
||||
| A | ||
| ||


