P0560 System Voltage
Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The battery supplies electricity to the ECM even when the ignition switch is in the off position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and sets the DTC.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0560 |
Open in ECM back-up power source circuit (1 trip detection logic) |
|
- HINT:
- If DTC P0560 is set, the ECM does not store other DTCs or the data stored in the ECM are partly erased.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK FUSE (EFI MAIN FUSE) |
![]() ![]() |
Remove the EFI MAIN fuse from the engine room No. 1 relay block.
Measure the resistance of the EFI MAIN fuse.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI MAIN fuse.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN FUSE, EFI MAIN FUSE - BATTERY) |
![]() ![]() |
Check the harness and the connector between the EFI MAIN fuse and ECM.
Remove the EFI MAIN fuse from the engine room No. 1 relay block.
Disconnect the A12 ECM connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
EFI MAIN fuse (2) - BATT (A12-20)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
EFI MAIN fuse (2) or BATT (A12-20) - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reinstall the EFI MAIN fuse.
Check the harness and the connector between the EFI MAIN fuse and battery.
Remove the EFI MAIN fuse from the engine room No. 1 relay block.
Disconnect the positive battery terminal.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
Battery positive terminal - EFI MAIN fuse (1)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
Battery positive terminal or EFI MAIN fuse (1) - Body ground
10 kΩ or higher
Reconnect the positive battery terminal.
Reinstall the EFI MAIN fuse.
|
|
||||
| OK | |
| 3. INSPECT BATTERY |
Check that the battery is not depleted.
- OK:
- Battery is not depleted.
|
|
||||
| OK | |
| 4. CHECK BATTERY TERMINAL |
Check that the battery terminals are not loose or corroded.
- OK:
- Battery terminals are not loose or corroded
|
|
||||
| OK | |
| 5. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Turn the ignition switch off and turn the tester OFF.
Start the engine and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT/ DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0560
A
No output
B
|
|
||||
| A | ||
| ||


