2005-2008 RAV4 · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION


w/ Entry and Start System
The cranking holding control system keeps energizing the ST relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch or park / neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.
A103821E15

w/o Entry and Start System
While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 12.4 mph (20 km/h) for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic):
  1. (a) Vehicle speed more than 12.4 mph (20 km/h)
  2. (b) Engine speed more than 1,000 rpm
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch (A/T*1)
  2. Clutch start switch*3 (M/T*1)
  3. ST relay circuit
  4. Ignition switch*2
  5. Cranking holding function circuit*3
  6. ECM
  1. *1: A/T denotes Automatic Transaxle models and M/T denotes Manual Transaxle models.
  2. *2: Only for w/o Entry and Start System.
  3. *3: Only for w/ Entry and Start System.

WIRING DIAGRAM

A127776E01
A127781E01

INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

Result:
Result
Proceed to
w/o Entry and Start System
A
w/ Entry and Start System
B



B
Go to step 11
A


2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON


Result:
Result
Proceed to
OK
A
NG (A/T Model)
B
NG (M/T Model)
C



A
CHECK INTERMITTENT PROBLEMS

C
Go to step 6
B


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. A107908E01
    Disconnect the B28 PNP switch connector.

  1. Measure the resistance when the transmission gear selector lever is moved to each position.

    Standard resistance:
    Gear Selector
    Lever Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    N
    2 - 9, 4 - 5
    D
    2 - 7
    2
    2 - 3
    L
    2 - 8

  1. Reconnect the PNP switch connector.



OK
Go to step 6
NG


4. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NEXT


5. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



OK
SYSTEM OK
NG


6. INSPECT IGNITION SWITCH ASSEMBLY

  1. A056879E33
    Disconnect the E5 ignition switch connector.

  1. Measure the resistance.

    Standard resistance:
    Ignition Switch Position
    Tester Connection
    Specified Condition
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    2 - 3
    Below 1 Ω
    ON
    2 - 3, 2 - 4, 6 - 7
    START
    1 - 2, 2 - 4, 6 - 7, 7 - 8

  1. Reconnect the ignition switch connector.



OK
Go to step 8
NG


7. REPLACE IGNITION SWITCH ASSEMBLY

NEXT


8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



OK
SYSTEM OK
NG


9. REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM [A/T MODEL], IGNITION SWITCH - STA TERMINAL OF ECM [M/T MODEL])

NEXT


10. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Drive the vehicle at more than 12.4 mph (20 km/h) for over 20 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC
    B



B
SYSTEM OK
A

REPLACE ECM

11. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to the on (IG) and engine start positions.

    OK:
    Ignition Switch Position
    Starter Signal
    on (IG)
    OFF
    Engine start
    ON



OK
REPLACE ECM
NG


12. INSPECT PARK / NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

  1. A107908E01
    Inspect the Park/Neutral Position (PNP) switch (for A/T models).
    1. Disconnect the B28 PNP switch connector.

    2. Measure the resistance when the transmission gear selector lever is moved to each position.

      Standard resistance:
      Gear Selector
      Lever Position
      Tester Connection
      Specified Condition
      P
      2 - 6, 4 - 5
      Below 1 Ω
      R
      1 - 2
      N
      2 - 9, 4 - 5
      D
      2 - 7
      2
      2 - 3
      L
      2 - 8

    3. Reconnect the PNP switch connector.

  1. A082259E10
    Inspect the clutch start switch (for M/T models).
    1. Disconnect the A4 clutch start switch connector.

    2. Measure the resistance when the clutch start switch is ON and OFF.

      Standard resistance:
      Ignition Switch Position
      Tester Connection
      Specified Condition
      on (pushed)
      1 - 2
      Below 1 Ω
      off (free)
      1 - 2
      10 kΩ or higher

    3. Reconnect the clutch start switch connector.



NG
REPLACE PARK / NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH
OK

CHECK CRANKING HOLDING FUNCTION CIRCUIT


← P0604 Internal Control Module Random Access Memory (RAM) Error (+ P0606, P0607, P0657) (from Nov 2005)P0617 Starter Relay Circuit High (Jan 2007 – Jul 2007) →