P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
| w/ Entry and Start System |
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch or park / neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the ST relay operating conditions based on the STA terminal voltage status.


| w/o Entry and Start System |
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 12.4 mph (20 km/h) for over 20 seconds.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0617 |
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic):
|
|
- *1: A/T denotes Automatic Transaxle models and M/T denotes Manual Transaxle models.
- *2: Only for w/o Entry and Start System.
- *3: Only for w/ Entry and Start System.
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the problem symptoms table (Click here).
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
| 1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM |
- Result:
Result
Proceed to
w/o Entry and Start System
A
w/ Entry and Start System
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
- Result:
Result
Proceed to
OK
A
NG (A/T Model)
B
NG (M/T Model)
C
|
|
||||
|
|
||||
| B | |
| 3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Disconnect the B28 PNP switch connector.

Measure the resistance when the transmission gear selector lever is moved to each position.
- Standard resistance:
Gear Selector
Lever Position
Tester Connection
Specified Condition
P
2 - 6, 4 - 5
Below 1 Ω
R
1 - 2
N
2 - 9, 4 - 5
D
2 - 7
2
2 - 3
L
2 - 8
Reconnect the PNP switch connector.
|
|
||||
| NG | |
| 4. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| NEXT | |
| 5. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
|
|
||||
| NG | |
| 6. INSPECT IGNITION SWITCH ASSEMBLY |
Disconnect the E5 ignition switch connector.

Measure the resistance.
- Standard resistance:
Ignition Switch Position
Tester Connection
Specified Condition
LOCK
All Terminals
10 kΩ or higher
ACC
2 - 3
Below 1 Ω
ON
2 - 3, 2 - 4, 6 - 7
START
1 - 2, 2 - 4, 6 - 7, 7 - 8
Reconnect the ignition switch connector.
|
|
||||
| NG | |
| 7. REPLACE IGNITION SWITCH ASSEMBLY |
| NEXT | |
| 8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
|
|
||||
| NG | |
| 9. REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM [A/T MODEL], IGNITION SWITCH - STA TERMINAL OF ECM [M/T MODEL]) |
| NEXT | |
| 10. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Drive the vehicle at more than 12.4 mph (20 km/h) for over 20 seconds.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0617
A
No DTC
B
|
|
||||
| A | ||
| ||
| 11. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the on (IG) and engine start positions.
- OK:
Ignition Switch Position
Starter Signal
on (IG)
OFF
Engine start
ON
|
|
||||
| NG | |
| 12. INSPECT PARK / NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH |
Inspect the Park/Neutral Position (PNP) switch (for A/T models).

Disconnect the B28 PNP switch connector.
Measure the resistance when the transmission gear selector lever is moved to each position.
- Standard resistance:
Gear Selector
Lever Position
Tester Connection
Specified Condition
P
2 - 6, 4 - 5
Below 1 Ω
R
1 - 2
N
2 - 9, 4 - 5
D
2 - 7
2
2 - 3
L
2 - 8
Reconnect the PNP switch connector.
Inspect the clutch start switch (for M/T models).

Disconnect the A4 clutch start switch connector.
Measure the resistance when the clutch start switch is ON and OFF.
- Standard resistance:
Ignition Switch Position
Tester Connection
Specified Condition
on (pushed)
1 - 2
Below 1 Ω
off (free)
1 - 2
10 kΩ or higher
Reconnect the clutch start switch connector.
|
|
||||
| OK | ||
| ||
