DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2007
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menu items: Powertrain / Engine and ECT / Data List.
Read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Notes
Calculate Load
Calculated load by ECM/
Min.: 0%, Max.: 100%
Idling: 10 to 25%
Running without load (2500 rpm): 7.5 to 14.5%
-
MAF
Air flow rate from Mass Air Flow meter/
Min.: 0 g/sec., Max.: 655.35 g/sec.
Idling: 3.2 to 8.2 g/sec.
Running without load (3000 rpm): 31 to 51 g/sec.
0 gm/s: Mass air flow sensor power source circuit is open or VG circuit is open/shorted
160 gm/s or more: E2G circuit is open
MAP
Absolute pressure inside intake manifold/
Min.: 0 kPa, Max.: 255 kPa
- Idling: 87 to 108 kPa
- Engine running at 2500 rpm: 105 to 120 kPa
- Engine running at 3000 rpm: 120 to 140 kPa
-
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383.75 rpm
Idling: 750 to 850 rpm
After warming up engine
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.: 140°C
After warming up engine: 80 to 95°C (176 to 203°F)
If value is -40°C (-40°F) or 140°C (284°F), sensor circuit is open or shorted
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to temperature at intake manifold
If value is -40°C (-40°F) or 140°C (284°F), sensor circuit is open or shorted
Fuel Press
Fuel pressure/
Min.: 0 MPa, Max.: 655.350 MPa
Idling: 38 to 43 MPa
-
EGR Position
EGR position/
Min.: 0%, Max.: 100%
Idling and after warmed up engine and vehicle is under normal atmospheric pressure: 0 to 60%
-
Accelerator Position No. 1
Accelerator position No. 1/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 8 to 28%
- Accelerator pedal depressed: 51 to 71%
-
Accelerator Position No. 2
Accelerator position No. 2/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 30 to 55%
- Accelerator pedal depressed: 73 to 98%
-
Throttle Position
Throttle position sensor/
Min.: 0%, Max.: 100%
Idling and after warmed up engine: 45 to 95%
-
Throttle Motor
Throttle actuator output /
Min.: 0%, Max.: 100%
Idling and after warmed up engine: 30 to 50%
-
AFS B1 S1
Air fuel ratio sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.999 V
Idling and after warmed up engine:
1.01 to 1.58 V
-
AF FT B1 S1
Short-term fuel trim associated with bank 1 sensor 1/
Min.: 0, Max.: 1.999
Value less than 1 (0.000 to 0.999): Rich
Value greater than 1 (1.001 to 1.999): Lean
-
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 120°C
Engine coolant temperature when engine starts
-
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 120°C
Intake air temperature when engine starts
-
Initial Exhaust Temp (In)
Exhaust temperature sensor for IN/
Min.: 0°C, Max.: 1000°C
Idling: 80 to 150°C
Idling after driving: 80 to 400°C
-
Initial Exhaust Temp (Out)
Exhaust temperature sensor for OUT/
Min.: 0°C, Max.: 1000°C
Idling: 80 to 150°C
Idling after driving: 80 to 400°C
-
Intake Air Temp (Turbo)
Intake air temperature (Turbo)/
Min.: -40°C to 190°C
65°C or less
-
DPF Differential Pressure
DPF differential pressure/
Min.: -5 kPa, Max.: 100 kPa
-3 kPa to 3 kPa
-
EGR Lift Position
EGR lift position/
Min.: 0%, Max.: 100%
Idling and after warmed up engine and vehicle is under normal atmospheric pressure: 0 to 60%
-
EGR Close Learning Value
EGR close learning value/
Min.: 0 V, Max.: 5 V
3.5 to 4.5 V
-
Throttle Valve Fully Closed
Throttle valve fully closed/
Min.: 0 deg, Max.: 84 deg
Engine is stopped: 14.25 to 21.25 deg
-
Target Common Rail Pressure
Target common rail pressure/
Min.: 0 kPa, Max.: 655350 kPa
Idling: 38 to 43 MPa
-
VNT Type
VN turbo type/
0: Not Avl, 1: Commo, 2: Vacuum, 3 CAN Commo
2: Vacuum
-
VNT Max Angle
VN turbo maximum angle /
Min.: 0%, Max.: 100%
100%
-
VNT Min Angle
VN turbo minimum angle /
Min.: 0%, Max.: 100%
0%
-
Exhaust Fuel Addition FB
Exhaust fuel addition correction value/
Min.: 0, Max.: 512
Vicinity of 1.0
-
Injection Pressure Correction
Injection pressure correction/
Min.: -500 mm3/st, Max.: 780 mm3/st
-400 to 400 mm3/st
-
Differential Pressure FB
Differential pressure correction/
Min.: -10 kPa, Max.: 246 kPa
Idling: -1.5 to 1.5 kPa
-
DPF Status Reju (PM)
Result of DPF catalyst regeneration (PM)/
Standby / Ready / Operate / Compl
-
-
EGR Valve Learning Value
EGR valve learning value/
Min.: 0 V, Max.: 5 V
-
-
Alternate Duty Ratio
Alternate duty ratio/
Min.: 0%, Max.: 100%
No electrical load: 10 to 80%
-
Accel Position 1
Accelerator pedal position sensor No. 1 voltage/
Min.: 0 V, Max.: 5 V
- Accelerator pedal released:
0.6 to 1.0 V
- Accelerator pedal depressed:
3.4 to 3.8 V
Read value with ignition switch on (IG)
(do not start engine)
Accel Position 2
Accelerator pedal position sensor No. 2 voltage/
Min.: 0 V, Max.: 5 V
- Accelerator pedal released:
1.4 to 1.8 V
- Accelerator pedal depressed:
4.2 to 4.6 V
Read value with ignition switch on (IG)
(do not start engine)
Accel Position
Accelerator pedal position sensor/
Min.: 0%, Max.: 100%
-
-
Fuel Temperature
Fuel temperature/
Min.: -40°C, Max.: 140°C
Idling and after warmed up engine: 0 to 80°C
-
VNT Command
VN turbo command/
Min.: 0%, Max.: 100%
-
-
Pump VCM Angle
Pump VCM angle/
Min.: 0 mA, Max.: 4000 mA
-
ECD Freeze Data
IDL Stable Control
IDL stable control/
Min.: -80 mm3/st, Max.: 79 mm3/st
-10 to 10 mm3/st
ECD Freeze Data
Diesel Throttle Angle
Diesel throttle angle/
Min.: -20%, Max.: 120%
Idling and after warmed up engine: 45 to 95%
-
Pilot 1 Injection
Pilot 1 Injection/
Min.: 0 μs, Max.: 65535 μs
Idling: 319 to 433 μs
-
Pilot 2 Injection
Pilot 2 Injection/
Min.: 0 μs, Max.: 65535 μs
Idling: 319 to 433 μs
-
Main Injection
Main Injection/
Min.: 0 μs, Max.: 65535 μs
Idling: 374 to 588 μs
-
After Injection
After Injection/
Min.: 0 μs, Max.: 65535 μs
-
-
Pilot 1 Injection
Pilot 1 Injection/
Min.: -70°CA, Max.: 20°CA
4.8 to 6.8°CA
-
Pilot 2 Injection
Pilot 2 Injection/
Min.: -50°CA, Max.: 20°CA
4.8 to 6.8°CA
-
Main Injection
Main Injection/
Min.: -90°CA, Max.: 90°CA
-6 to 0°CA
-
After Injection
After Injection/
Min.: -10°CA, Max.: 50°CA
-
-
Injection Feedback Value
Injection volume feedback learning value/
Min.: -10 mm3/st, Max.: 9.92 mm3/st
Idling: -2.0 to 2.0 mm3
-
Injection Feedback Val #1
Injection volume correction for cylinder 1/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.5 to 3.5 mm3
-
Injection Feedback Val #2
Injection volume correction for cylinder 2/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.5 to 3.5 mm3
-
Injection Feedback Val #3
Injection volume correction for cylinder 3/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.5 to 3.5 mm3
-
Injection Feedback Val #4
Injection volume correction for cylinder 4/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.5 to 3.5 mm3
-
Injection Volume
Injection volume/
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
Idling: 3.1 to 7.6 mm3
-
DPF Catalyst Deteriorate
DPF Catalyst Deteriorate/
0: Normal, 1: Deteriorated
Normal
-
DPF No Activate
DPF operation/
0: Activate, 1: No Activate
Active
-
DPF PM Block
DPF PM Block/
0: No Blocked, 1: Blocked
No blocked
-
Injector Memory Error
EEPROM malfunction for injector/
0: No Error, 1: Error
No error
-
Catalyst Memory Error
EEPROM malfunction for DPF catalyst/
0: No Error, 1: Error
No error
-
Target Booster Pressure
Target boost pressure/
Min.: 0 kPa, Max.: 320 kPa
Idling and after warmed up engine and vehicle is under normal atmospheric pressure: 89 to 100 kPa
-
Diesel Throttle Learn Status
Diesel throttle learning status/
OK or NG
OK
-
EGR Learning Status
EGR learning status/
OK or NG
OK
-
ACC Relay
ACC relay/
ON or OFF
ON: Cranking
-
Starter Relay
Starter relay/
ON or OFF
ON: Cranking
-
Starter Signal
Starter signal/
ON or OFF
ON: Cranking
-
Starter Control
Starter switch/
ON or OFF
ON: Cranking
-
A/C Signal
Air conditioning signal/
ON or OFF
ON: Air conditioner ON
-
Neutral Position SW Signal
Park/Neutral position switch/
ON or OFF
-
-
Stop Light Switch
Stop light switch/
ON or OFF
- ON: Brake pedal depressed
- OFF: Brake pedal released
-
Battery Voltage
Battery voltage/
Min.: 0 V Max.: 65.535 V
Idling: 9 to 14 V
-
Atmosphere Pressure
Atmospheric pressure value/
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1912.6 mmHg, 75.3 in.Hg)
Actual atmospheric pressure
-
Battery Current
Battery Current/
Min.: -100 A, Max.: 100 A
-
Charging control service data
Battery Temperature
Battery temperature/
Min.: -45°C, Max.: 156.4°C
-
Charging control service data
Alternator Output Duty
Generator output duty/
Min.: 0%, Max.: 100%
-
Electricity generated by alternator is output through duty ratio charging control service data
Alt Vol - Non Active Test
Request voltage when regulator not under forced activation/
Min.: 0 V, Max.: 20 V
Battery electrolyte temperature varies (12.5 to 14.8 V) while driving: After engine start
Alternator regulator output voltage is output when performing Active Test, value is OV
Alt Vol - Active Test
Request voltage when regulator under forced activation/
Min.: 0 V, Max.: 20 V
Request instruction voltage value: After engine start
Charging control service data When not performing Active Test, value is OV
Electric Fan Motor
Radiator cooling fan motor/
ON or OFF
ON: The radiator cooling fan motor activated
-
TC and TE1
TC and TE1 terminals of DLC3/
ON or OFF
-
-
# Codes
#Code/
Min.: 0, Max.: 255
-
Number of detected DTCs
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
Click here
SPD Test
SPD test/
COMPL or INCMPL
-
-
MIL
MIL status/
ON or OFF
ON: MIL ON
-
MIL ON Run Distance
MIL ON Run Distance/
Min.: 0 km, Max.: 65535 km
Distance after DTC detected
-
Running Time from MIL ON
Running Time from MIL ON/
Min.: 0 minute, Max.: 65535 minutes
Equivalent running time after MIL was ON
-
Engine Run Time
Engine run time/
Min.: 0 second, Max.: 65535 seconds
Time after engine started
Service data
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 minute, Max.: 65535 minutes
Equivalent to time after DTCs were erased
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km/h, Max.: 65535 km/h
Equivalent to drive distance after DTCs were erased
-
Warmup Cycle Cleared DTC
Warm up cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warm up cycles after DTC cleared
Number of Emission DTC
Number of emission related DTCs/ ON or OFF
-
-
Complete Parts Monitor
Comprehensive component monitor/
NOT AVL or AVAIL
-
-
Fuel System Monitor
Fuel system monitor/
NOT AVL or AVAIL
-
-
EGR Monitor
EGR monitor/
NOT AVL or AVAIL
-
EGR Monitor
EGR Monitor
EGR monitor/
COMPL or INCMPL
-
-
Model Code
Identifying model code
ALA30
-
Engine Type
Identifying engine type
2ADFTV
-
Cylinder Number
Identifying cylinder number/
Min.: 0, Max.: 255
4
-
Transmission Type
Identifying transmission type
M/T
-
Destination
Identifying destination
W
-
Model Year
Identifying model year/
Min.: 1900, Max.: 2155
2007
-
System Identification
Identifying engine system
Diesel
-
- Idling: 87 to 108 kPa
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Notes
Connect the TC and TE1
Turn on TC and TE1 connection
ON/OFF
-
Control the Electric Cooling Fan
Control the electric cooling fan operation
ON/OFF
Test is possible when following conditions are met: - Ignition switch on (IG)
- Engine is stopped
Activate the Starter Relay
Starter relay
ON/OFF
-
Activate the ACC Cut Relay
ACC cut relay
ON/OFF
-
Control the EGR Step Position
Control the EGR valve position
0 to 100%
-
Activate the DPF Rejuvenate (PM)
DPF catalyst regeneration (PM)
Raise temperature of DPF to more than 600°C (1112°F) by adding fuel intermittently using the exhaust fuel addition injector
ON/OFF
-
Test the Turbo Charger Step Motor
Control the E-VRV for turbocharger control
0 to 100%
-
Test the Fuel Leak
Pressurizes common rail internal fuel pressure, and checks for fuel leaks
Stop/Start
- Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when ON is selected
- Above conditions preserved while tester is ON
Control the Voltage of Alternator
Request output voltage of generator regulator during forced activation
12.5 to 14.8 V
Test possible while vehicle stopped and engine idling.
Control the Cylinder#1 Fuel Cut
Cut off fuel injection from No. 1 injector
ON/OFF
Fuel injection stopped while tester is ON
Control the Cylinder#2 Fuel Cut
Cut off fuel injection from No. 2 injector
ON/OFF
Fuel injection stopped while tester is ON
Control the Cylinder#3 Fuel Cut
Cut off fuel injection from No. 3 injector
ON/OFF
Fuel injection stopped while tester is ON
Control the Cylinder#4 Fuel Cut
Cut off fuel injection from No. 4 injector
ON/OFF
Fuel injection stopped while tester is ON
- Ignition switch on (IG)