DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
| READ DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List.
ECM: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Notes
Calculate Load
Calculated load by ECM/
Min.: 0%, Max.: 100%
Idling: 10 to 25%
Running without load (2,500 rpm): 7.5 to 14.5%
-
MAF
Air flow rate from mass air flow sensor/
Min.: 0 g/sec., Max.: 655.35 g/sec.
Idling: 2.8 to 5.2 g/sec.
Running without load (2,500 rpm): 27.5 to 32.5 g/sec.
0 g/sec.: Mass air flow sensor power source circuit is open or VG circuit is open/shorted
160 g/sec. or more: E2G circuit is open
MAP
Absolute pressure inside intake manifold/
Min.: 0 kPa, Max.: 255 kPa
- Idling: 85 to 93 kPa
- Engine running at 2,500 rpm: 105 to 120 kPa
- Engine running at 3,000 rpm: 120 to 140 kPa
-
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383.75 rpm
Idling: 750 to 1,200 rpm
After warming-up engine
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
After warming up engine: 75 to 95°C (167 to 203°F)
If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air
Intake air temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Equivalent to temperature at intake manifold
If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Fuel Press
Fuel pressure/
Min.: 0 kPa, Max.: 655,350 kPa
Idling: 37 to 43 MPa
-
EGR Position
EGR position/
Min: 0%, Max: 100%
Idling after engine warmed-up and vehicle is under normal atmospheric pressure: 0 to 60%
-
Accelerator Position No. 1
No. 1 accelerator position/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 8 to 28%
- Accelerator pedal depressed: 51 to 71%
-
Accelerator Position No. 2
No. 2 accelerator position/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 30 to 55%
- Accelerator pedal depressed: 73 to 98%
-
Throttle Position
Throttle position sensor/
Min.: 0%, Max.: 100%
warmed-up and idling: 81 to 95%
-
Throttle Motor
Throttle actuator output /
Min.: 0%, Max.: 100%
Idling after engine warmed up: 30 to 50%
-
AFS B1 S1
A/F sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.999 V
Idling after engine warmed-up:
1.01 to 1.58 V
-
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C (-40°F), Max.: 120°C (248°F)
ECT when engine starts
-
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C (-40°F), Max.: 120°C (248°F)
IAT when engine starts
-
Initial Exhaust Temp (In)
Exhaust temperature sensor for IN/
Min.: 0°C (32°F), Max.: 1,000°C (1,832°F)
Idling: 80 to 150°C (66 to 302°F)
Idling after driving: 80 to 400°C (66 to 752°F)
-
Initial Exhaust Temp (Out)
Exhaust temperature sensor for OUT/
Min.: 0°C (32°F), Max.: 1,000°C (1,832°F)
Idling: 80 to 150°C (66 to 302°F)
Idling after driving: 80 to 400°C (66 to 752°F)
-
Intake Air Temp (Turbo)
Intake Air Temperature (Turbo)/
Min.: -40 to 140°C (-40 to 284°F)
65°C (58°F) or less
-
DPNR Differential Pressure
DPNR differential pressure/
Min.: -5 kPa, Max.: 100 kPa
-3 kPa to 3 kPa
-
EGR Lift Position
EGR position/
Min.: 0%, Max.: 100%
Idling after engine warmed-up and vehicle is under normal atmospheric pressure: 0 to 60%
-
EGR Close Learning Value
EGR close learning value/
Min: 0 V, Max: 5 V
3.5 to 4.5 V
-
Throttle Valve Fully Closed
Throttle valve fully closed/
Min.: 0 deg, Max.: 84 deg
-
-
Target Common Rail Pressure
Target common rail pressure/
Min.: 0 kPa, Max.: 655,350 kPa
Idling: 35 to 45 MPa
-
VNT Type
VN turbo type/
0: Not Avl, 1: Commo, 2: Vacuum
2: Vacuum
-
VNT Max Angle
VN turbo maximum angle /
Min.: 0%, Max.: 100%
100%
-
VNT Min Angle
VN turbo minimum angle /
Min.: 0%, Max.: 100%
10%
-
Exhaust Fuel Addition FB
Exhaust fuel addition correction value/
Min.: 0, Max.: 512
In the vicinity of 1.0
-
Injection Pressure Correction
Injection pressure correction/
Min.: -500 mm3/st, Max.: 780 mm3/st
-400 to 400 mm3/st
-
DNPR A/F
Min.: 0 V, Max.: 127 V
Idling after engine warmed-up: 30 to 50 V
-
Differential Pressure FB
Differential pressure correction/
Min.: -10 kPa, , Max.: 246 kPa
Idling: -1.5 to 1.5 kPa
-
DPNR Status Reju (S)
Result of DPNR catalyst regeneration (S)/
ON or OFF
OFF
-
DPNR Status Reju (PM)
Result of DPNR catalyst regeneration (PM)/
ON or OFF
OFF
-
EGR Valve Learning Value
EGR lift learning value/
Min.: 0 deg, Max.: 5 deg
-
-
Alternate Duty Ratio
Alternate duty ratio/
Min.: 0%, Max.: 100%
No electrical load: 10 to 80%
-
Accel Position 1
No. 1 accelerator pedal position sensor voltage/
Min.: 0 V, Max.: 5 V
- Accelerator pedal released:
0.6 to 1.0 V
- Accelerator pedal depressed:
3.4 to 3.8 V
Read value with ignition switch on (IG)
(do not start engine)
Accel Position 2
No. 2 accelerator pedal position sensor voltage/
Min.: 0 V, Max.: 5 V
- Accelerator pedal released:
1.4 to 1.8 V
- Accelerator pedal depressed:
4.2 to 4.6 V
Read value with ignition switch on (IG)
(do not start engine)
Accel Position
Accelerator position status/
Min.: 0%, Max.: 100%
- Accelerator pedal released: 0%
- Accelerator pedal depressed: 100%
Read value with ignition switch on (IG) (do not start engine)
Fuel Temperature
Fuel temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Idling after engine warmed-up: 0 to 80°C (32 to 66°F)
-
Diesel Throttle Angle
Diesel throttle angle/
Min.: -20%, Max.: 120%
Idling after engine warmed-up: 81 to 95%
-
VNT Command
VN turbo command/
Min.: 0%, Max.: 100%
-
-
Pump VCM Angle
Pump VCM angle/
Min.: 0 mA, Max.: 4,000 mA
-
ECD Freeze Data
IDL Stable Control
IDL stable control/
Min.: -80 mm3/st, Max.: 79 mm3/st
-5 to 5 mm3/st
ECD Freeze Data
Pilot 1 Injection
Pilot 1 injection/
Min.: 0 μsec., Max.: 65,535 μsec.
Idling after engine warmed-up: 0 μsec.
-
Pilot 2 Injection
Pilot 2 injection/
Min.: 0 μsec., Max.: 65,535 μsec.
Idling: 148 to 194 μsec.
-
Main Injection
Main injection/
Min.: 0 μsec., Max.: 65,535 μsec.
Idling: 173 to 368 μsec.
-
After Injection
After injection/
Min.: 0 μsec., Max.: 65,535 μsec.
-
-
Pilot 1 Injection
Pilot 1 injection/
Min.: -70 crankshaft angle, Max.: 20 crankshaft angle
-
-
Pilot 2 Injection
Pilot 2 injection/
Min.: -50 crankshaft angle, Max.: 20 crankshaft angle
-1.25 to -4.5 crankshaft angle
-
Main Injection
Main injection/
Min.: -90 crankshaft angle, Max.: 90 crankshaft angle
-6 to 0 crankshaft angle
-
After Injection
After injection/
Min.: -10 crankshaft angle, Max.: 50 crankshaft angle
-
-
Injection Feedback Value
Injection volume feedback learning value/
Min.: -10 mm3/st, Max.: 9.92 mm3/st
Idling: -0.4 to 1.0 mm3/st
-
Injection Feedback Val #1
Injection volume correction for cylinder 1/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.0 to 3.0 mm3/st
-
Injection Feedback Val #2
Injection volume correction for cylinder 2/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.0 to 3.0 mm3/st
-
Injection Feedback Val #3
Injection volume correction for cylinder 3/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.0 to 3.0 mm3/st
-
Injection Feedback Val #4
Injection volume correction for cylinder 4/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.0 to 3.0 mm3/st
-
Injection Volume
Injection volume/
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
Idling: 3.9 to 7.0 mm3/st
-
DPNR Catalyst Deteriorate
DPNR catalyst deterioration/
0: Normal, 1: Deteriorated
Normal
-
DPNR No Activate
DPNR operation/
0: Activated, 1: Not Activated
Activated
-
DPNR PM Block
DPNR PM block/
0: Not blocked, 1: Blocked
Not blocked
-
Injector Memory Error
EEPROM malfunction for injector/
0: No error, 1: Error
No error
-
Catalyst Memory Error
EEPROM malfunction for DPNR catalyst/
0: No error, 1: Error
No error
-
Target Booster Pressure
Target boost pressure/
Min.: 0 kPa, Max.: 320 kPa
Idling after engine warmed up and vehicle is under normal atmospheric pressure: 89 to 100 kPa
-
Diesel Throttle Learn Status
Diesel throttle learning status/
0: NG, 1: OK
OK
-
EGR Learning Status
EGR learning status/
0: NG, 1: OK
OK
-
ACC Relay
ACC relay/
ON or OFF
ON: Cranking
-
Starter Relay
Starter relay/
ON or OFF
ON: Cranking
-
Starter Signal
Starter signal/
ON or OFF
ON: Cranking
-
Starter Control
Starter switch status/
ON or OFF
ON: Cranking
-
A/C Signal
A/C signal/
ON or OFF
ON: A/C ON
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
ON: P or N position
-
Stop Light Switch
Stop light switch/
ON or OFF
- ON: Brake pedal depressed
- OFF: Brake pedal released
-
Battery Voltage
Battery voltage/
Min.: 0 V Max.: 65.535 V
Idling: 9 to 14 V
-
Atmosphere Pressure
Atmospheric pressure value/
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1,912.6 mmHg, 75.3 in.Hg)
Actual atmospheric pressure
-
Battery Current
Battery current/
Min.: -100 A, Max.: 100 A
-
Charging control service data
Battery Temperature
Battery temperature/
Min.: -45°C (-49°F), Max.: 156.4 °C (313.5°F)
-
Charging control service data
Alternator Output Duty
Alternator output duty/
Min.: 0%, Max.: 100%
-
Electricity generated by alternator is output through duty ratio
Charging control service data
Alt Vol - Non Active Test
Request voltage when regulator not under forced activation/
Min.: 0 V, Max.: 20 V
Battery electrolyte temperature varies (12.5 to 14.8 V) while driving:
After engine start
Alternator regulator output voltage is out put
When performing Active Test, value is 0 V
Alt Vol - Active Test
Request voltage when regulator under forced activation/
Min.: 0 V, Max.: 20 V
Request instruction voltage value:
After engine start
Charging control service data
When not performing Active Test, value is 0 V
Electric Fan Motor
Radiator cooling fan motor/
ON or OFF
ON: Active the radiator cooling fan motor
-
TC and TE1
TC and TE1 terminal of DLC3
ON or OFF
-
-
#Codes
#Codes/
Min.: 0, Max.: 255
-
Number of detected DTCs
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
(Click here)
SPD Test
Check mode result for vehicle speed sensor:
0: COMPL, 1: INCMPL
-
-
MIL ON Run Distance
MIL ON run distance/
Min.: 0 km, Max.: 65,535 km
Distance after DTC detected
-
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min, Max.: 65,535 min
Equivalent running time after MIL was ON
-
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65,535 s
Time after engine started
Service data
Time After DTC Cleared
Time after DTC cleared/
Min.: 0 min, Max.: 65,535 min
Equivalent to time after DTCs were erased
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km, Max.: 65,535 km
Equivalent to drive distance after DTCs were erased
-
Warm up Cycle Cleared DTC
Warm up cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warm up cycles after DTC cleared
Number of Emission DTC
Number of emission DTCs
-
-
EGR Monitor
EGR monitor/
0: NOT AVL, 1: AVAIL
-
EGR monitor
EGR Monitor
EGR monitor/
0: COMPL, 1: INCMPL
-
EGR monitor
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
0: NOT AVL, 1: AVAIL
-
O2S (A/FS) heater monitor
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
0: COMPL, 1: INCMPL
-
O2S (A/FS) heater monitor
O2S(A/FS) Monitor
O2S (A/FS) monitor/
0: NOT AVL, 1: AVAIL
-
O2S (A/FS) monitor
O2S(A/FS) Monitor
O2S (A/FS) monitor/
0: COMPL, 1: INCMPL
-
O2S (A/FS) monitor
Model Code
Model code
-
Identifying model code/
ACA3#
Engine Type
Engine type
-
Identifying engine type/
2AD#
Cylinder Number
Cylinder number/
Min.: 0, Max.: 255
-
Identifying cylinder number/
4
Destination
Destination
-
Identifying destination/
W
Model Year
Model year/
Min.: 1900 MY, Max.: 2155 MY
-
Identifying model year/
200#
- HINT:
- *: If no idling conditions are specified, the shift lever is in the neutral position, and the A/C switch and all accessory switches are OFF.
- Idling: 85 to 93 kPa
| PERFORM ACTIVE TEST |
- HINT:
- Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
ECM: Tester Display
Test Part
Control Range
Diagnostic Notes
Connect the TC and TE1
Turn on TC and TE1 connection
ON/OFF
-
Control the Electric Cooling Fan
Control the electric cooling fan operation
ON/OFF
Test possible when following conditions met: - ignition switch on (IG)
- Engine is stopped
Activate the Starter Relay
Starter
ON/OFF
Test possible when engine stopped
Activate the ACC Cut Relay
Active ACC (Accessory) relay
ON/OFF
Test possible when engine stopped
Control the EGR Step Position
Control the EGR valve position
1 to 100%
-
Activate the DPNR Rejuvenate (S)
DPNR catalyst regeneration (S)
Raise temperature of DPNR to more than 600°C (1,112°F) by adding fuel intermittently using the exhaust fuel addition injector
ON/OFF
-
Activate the DPNR Rejuvenate (PM)
DPNR catalyst regeneration (PM)
Raise temperature of DPNR to more than 600°C (1,112°F) by adding fuel intermittently using the exhaust fuel addition injector
ON/OFF
-
Test the Turbo Charger Step Motor
Control the VRV for turbocharger control
0 to 100%
-
Test the Fuel Leak
Pressurizes common rail internal fuel pressure, and checks for fuel leaks
Stop/Start
- Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
- Above conditions preserved while test is ON
Control the Voltage of Alternator
Request output voltage of generator
Between 12.5 and 14.8 V
Test possible while vehicle stopped and engine idling
Control the Cylinder#1 Fuel Cut
Cut off fuel injection from No. 1 injector
ON/OFF
Fuel injection stopped while test is ON
Control the Cylinder#2 Fuel Cut
Cut off fuel injection from No. 2 injector
ON/OFF
Fuel injection stopped while test is ON
Control the Cylinder#3 Fuel Cut
Cut off fuel injection from No. 3 injector
ON/OFF
Fuel injection stopped while test is ON
Control the Cylinder#4 Fuel Cut
Cut off fuel injection from No. 4 injector
ON/OFF
Fuel injection stopped while test is ON
Control the All Cylinders Fuel Cut
All cylinder injector fuel cut
ON/OFF
Test possible during vehicle stopping
- ignition switch on (IG)