2005-2008 RAV4 · Service Manual ENGINE

REGISTRATION

Other · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

NOTICE:
  1. When an injector is replaced, the injector's compensation code must be input into the ECM (Proceed to step 1).
  2. When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM (Proceed to step 2).


1. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

NOTICE:
Injector compensation codes are unique, 30-digit, and alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

HINT:
The injector compensation code is imprinted on the head portion of each injector.

  1. A156012E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

    NOTICE:
    Do not start the engine.

  1. Turn the tester on.

  1. A122614
    Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.

  1. Press "Next".

  1. A122615
    Press "Next" again to proceed.

  1. A122622
    Select "Set Compensation Code".

  1. Press "Next".

  1. A122617
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press "Next".

  1. A160294
    Register the compensation code.

    1. Press "Input".

    2. A096465E01
      Manually input the cylinder's compensation code using the keyboard on the tester screen. The code is a 30-digit, alphanumeric value imprinted on the injector's head portion.

      HINT:
      Each injector compensation code is unique. The correct compensation code must be input into each cylinder selected on the tester.

    3. Confirm that the compensation code is correct for the selected cylinder, and then press "OK".

  1. A160295
    Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the injector.

    NOTICE:
    If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    HINT:
    1. If a wrong compensation code was input or read, return to the "Input Value" screen by pressing "Input".
    2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

  1. Press "Next" to set the compensation code to the ECM.

    HINT:
    1. If the setting process fails, the compensation code may be incorrect. Check the compensation code again.
    2. If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

  1. A122626
    To continue with compensation code registrations for other cylinders, press "Next". To finish the registration, press "Cancel".

  1. Turn the ignition switch off and then turn the tester off.

  1. Wait for at least 30 seconds.

  1. Turn the ignition switch to the ON position and then turn the tester on.

  1. Clear DTC P1601 stored in the ECM using the tester (Click here).


2. INPUT ALL INJECTOR COMPENSATION CODES AND TRANSFER CATALYST RECORD OF DPF THERMAL DETERIORATION

NOTICE:
Injector compensation codes are unique, 30-digit, and alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

HINT:
The following operation is available with ECMs that can transmit the registered injector compensation codes and catalyst record of DPF thermal deterioration to the intelligent tester.

  1. Read the catalyst record of DPF thermal deterioration.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position.

      NOTICE:
      Do not start the engine.

    3. Turn the tester on.

    4. A160280
      Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Catalyst Record Transferring.

    5. Press "Next".

    6. A160281
      Press "Next" again to proceed.

    7. A160282
      Press "Next" again to proceed.

    8. A160283
      Select "Step 1 Read catalyst record".

    9. Press "Next".

    10. A160284
      Confirm the catalyst record and press "Next".

      NOTICE:
      If a code cannot be read, replace the DPF catalyst with a new one.

      HINT:
      When installing a new ECM that has registered catalyst record such as "FFFFFFFF", perform the procedures below by following the prompts on the tester screen.
      1. When replacing only the ECM, be sure to transfer the catalyst record from the removed ECM to the new ECM.
      2. When replacing the DPF catalyst, clear the catalyst record registered in the ECM (Click here).

    11. A113707
      If the catalyst record has already been stored in the tester, the message in the illustration will appear. Press "Replace".

    12. A160285
      Press "Exit".

  1. A156012E01
    Read the injector compensation codes.

    1. A122614
      Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.

    2. Press "Next".

    3. A122615
      Press "Next" again to proceed.

    4. A122616
      Select "Read Compensation Code".

    5. Press "Next".

    6. A122617
      Select the number of the cylinder corresponding to the injector compensation code that you want to read.

    7. Press "Next".

      HINT:
      The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

    8. A160296
      Check that the injector compensation code (30-digit alphanumeric value) is displayed on the tester screen.

    9. Press "Save".

    10. A108923E01
      Check that the compensation code displayed on the tester screen is correct.

    11. Press "Save" or "Replace" to save the injector compensation code.

      HINT:
      1. The existing compensation code is overwritten with the new compensation code and is deleted from the tester.
      2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

    12. A160296
      To read and save injector compensation codes for other cylinders, press "Next" to continue. To finish this operation, press "Cancel".

    13. Turn the ignition switch off.

    14. Turn the tester off.

  1. Replace the ECM (Click here).

  1. Set the catalyst record of DPF thermal deterioration.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position.

    3. Turn the tester on.

    4. A130547
      Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Catalyst Record Transferring.

    5. Press "Next".

    6. A130548
      Press "Next" again to proceed.

    7. A130549
      Press "Next" again to proceed.

    8. A160288
      Select "Step 3 Set catalyst record".

    9. A160286
      Confirm the catalyst record and press "Next".

    10. A160287
      Press "Exit".

  1. A156012E01
    Set the injector compensation code.

    NOTICE:
    Do not start the engine.

    HINT:
    The injector compensation code is imprinted on the head portion of each injector.


    1. A122614
      Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.

    2. Press "Next".

    3. A122615
      Press "Next" again to proceed.

    4. A122622
      Select "Set Compensation Code".

    5. Press "Next".

    6. A122617
      Select the number of the cylinder corresponding to the injector compensation code that you want to read.

    7. Press "Next".

    8. A160295
      Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the injector.

      NOTICE:
      If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

      HINT:
      If a wrong compensation code was input or read, return to the "Input Value" screen by pressing "Input". The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

    9. Press "Next" to set the compensation code to the ECM.

      HINT:
      1. If the setting fails, the compensation code may be incorrect. Check the compensation code again.
      2. If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and repeat this operation.

    10. A122626
      To continue with compensation code registrations for other cylinders, press "Next". To finish the registration, press "Cancel".

  1. Clear DTC P1601 stored in the ECM using the tester.

    1. Turn the ignition switch off and then turn the tester off.

    2. Wait for at least 30 seconds.

    3. Turn the ignition switch to the ON position and then turn the tester on.

    4. Clear DTC P1601 (Click here).

← BASIC INSPECTION (from Jan 2007)REGISTRATION (from Aug 2007) →