2005-2008 RAV4 · Service Manual ENGINE

Engine Difficult to Start or Stalling

Circuit diagnosis · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing a supply pump, the ECM needs initialization (Click here).
  3. After replacing an injector, the ECM needs registration (Click here).

HINT:
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


1. CHECK OUTPUT DTC (RELATED TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    DTCs related to engine
    B



B
REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT
A


2. CHECK FUEL FILTER ASSEMBLY
  1. Check that the fuel filter is not clogged.

    OK:
    Fuel filter is not clogged.



NG
REPLACE FUEL FILTER ASSEMBLY
OK


3. CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

  1. Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.

    OK:
    Engine cranking condition is normal.



NG
CHECK AND REPLACE BATTERY, CHARGING SYSTEM, STARTER ASSEMBLY AND STARTING SYSTEM
OK


4. READ VALUE USING FUEL PRESSURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Read the value.

    Standard value:
    Item
    Inspection Condition
    Reference Value
    Fuel Press
    Cranking, and engine coolant temperature 0°C (32°F) or more
    25 to 35 MPa



NG
BLEED AIR FROM FUEL SYSTEM
OK


5. CHECK IF INITIAL COMBUSTION OCCURS
  1. Check if initial combustion occurs.

    Result:
    Result
    Proceed to
    No initial combustion with cold engine
    A
    No initial combustion with hot engine
    B
    Initial combustion occurs
    C



B
Go to step 7

C
Go to step 8
A


6. CHECK GLOW INDICATOR LIGHTING TIME AND AFTER-GLOW TIME
  1. Check the lighting duration of the glow indicator light (Click here).

    OK:
    Indicator lighting time is normal.



NG
REPAIR OR REPLACE PRE-HEATING SYSTEM
OK


7. READ VALUE USING FUEL PRESSURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Read the values.

    OK:
    The internal fuel pressure of the common rail is within the specification below.
    Engine Speed
    Fuel Pressure
    Idling
    Approximately 35 to 40 MPa
    3,000 rpm (No engine load)
    Approximately 78 to 88 MPa



NG
Go to step 13
OK


8. CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
  1. Inspect the engine condition (Click here).



NG
REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST
OK


9. READ VALUE USING FUEL PRESSURE SENSOR AND INJECTOR
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Select the following menu items in order and read the values.

    1. Fuel Press
    2. Injection Volume

    Standard value:
    Item
    Engine Speed*
    Reference Value
    Fuel Press
    Idling
    35 to 40 MPa
    Fuel Press
    2,000 rpm (No engine load)
    65 to 78 MPa
    Fuel Press
    3,000 rpm (No engine load)
    78 to 88 MPa
    Injection Volume
    Idling
    4.5 to 9.0 mm3
    Injection Volume
    2,000 rpm (No engine load)
    5.0 to 9.5 mm3
    Injection Volume
    3,000 rpm (No engine load)
    6.6 to 11.1 mm3

    HINT:
    *: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



NG
Go to step 14
OK


10. CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the cylinder compression pressure (Click here).

    Standard pressure:
    2,700 kPa (27.5 kgf/cm2, 392 psi)

    Minimum pressure:
    2,200 kPa (22.4 kgf/cm2, 319 psi)

    Difference between each cylinder:
    500 kPa (5.1 kgf/cm2, 73 psi)



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


11. CHECK WIRE HARNESS (INJECTOR - EDU)
A130528E01
  1. Disconnect the B36, B37, B38, and B39 injector connectors.

  1. Disconnect the B64 EDU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B36-1 - B64-4 (INJ1)
    Below 1 Ω
    B37-1 - B64-2 (INJ2)
    Below 1 Ω
    B38-1 - B64-1 (INJ3)
    Below 1 Ω
    B39-1 - B64-3 (INJ4)
    Below 1 Ω
    B36-2 - B64-5 (COM1)
    Below 1 Ω
    B37-2 - B64-6 (COM2)
    Below 1 Ω
    B38-2 - B64-6 (COM2)
    Below 1 Ω
    B39-2 - B64-5 (COM1)
    Below 1 Ω
    B36-1 or B64-4 (INJ1) - Body ground
    10 kΩ or higher
    B37-1 or B64-2 (INJ2) - Body ground
    10 kΩ or higher
    B38-1 or B64-1 (INJ3) - Body ground
    10 kΩ or higher
    B39-1 or B64-3 (INJ4) - Body ground
    10 kΩ or higher
    B36-2 or B64-5 (COM1) - Body ground
    10 kΩ or higher
    B37-2 or B64-6 (COM2) - Body ground
    10 kΩ or higher
    B38-2 or B64-6 (COM2) - Body ground
    10 kΩ or higher
    B39-2 or B64-5 (COM1) - Body ground
    10 kΩ or higher

  1. Reconnect the injector connectors.

  1. Reconnect the EDU connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


12. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL CYLINDER FUEL CUT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.

  1. Check the engine idle speed while the fuel injection to each cylinder is cut using the tester.

    Result:
    Engine Idling Condition
    Proceed to
    Becomes unstable
    A
    Does not change
    B

    HINT:
    Replace the injector mounted on the cylinder that causes no significant idle speed change.



B
REPLACE INJECTOR ASSEMBLY
A

REPLACE INJECTOR DRIVER

13. CHECK IF FUEL IS BEING SUPPLIED TO SUPPLY PUMP
  1. Disconnect the inlet hose from the supply pump.

  1. Operate the priming pump and check that the fuel is being supplied to the supply pump.

    OK:
    Fuel is properly supplied to the supply pump when the priming pump is operated.

  1. Reconnect the inlet hose.



OK
REPLACE SUPPLY PUMP ASSEMBLY
NG

CHECK AND REPLACE FUEL PIPE CLOGGING (INCLUDING FUEL FREEZING) (FUEL TANK - SUPPLY PUMP)

14. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard value:
    Between 75 and 95°C (167 and 203°F) with warm engine.



NG
Go to step 18
OK


15. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the value.

    Standard value:
    Between 750 to 1,000 rpm with warm engine (A/C switch OFF).



NG
Go to step 19
OK


16. CHECK WIRE HARNESS (STARTER RELAY - ECM)
A134299E01
w/ Entry and start system:

  1. A130323E01
    Remove the ST relay from the No. 8 relay block.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    ST relay terminal 1 - A12-43 (STA)
    Below 1 Ω
    ST relay terminal 1 or A12-43 (STA) - Body ground
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the ECM connector.

w/o Entry and start system:
  1. Inspect the STA fuse.

    1. Remove the STA fuse from the engine room No. 1 relay block.

    2. Measure the resistance of the fuse.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the STA fuse.

  1. Check the wire harness between the ignition switch and ECM.

    1. Disconnect the E5 ignition switch connector.

    2. Disconnect the A12 ECM connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      E5-8 (ST2) - A12-43 (STA)
      Below 1 Ω
      E5-8 (ST2) or A12-43 (STA) - Body ground
      10 kΩ or higher

    4. Reconnect the ignition switch.

    5. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


17. READ VALUE USING INTELLIGENT TESTER (FUEL PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Read the value.

    Standard value:
    35 to 40 MPa engine idling.



NG
Go to step 20
OK

REPLACE ECM

18. INSPECT ENGINE COOLANT TEMPERATURE SENSOR

  1. A081700E11
    Remove the engine coolant temperature sensor.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Connection
    Specified Condition
    20°C (68°F)
    2.32 to 2.59 kΩ
    80°C (176°F)
    0.310 to 0.326 kΩ

    NOTICE:
    When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.

    HINT:
    Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.

  1. Reconnect the engine coolant temperature sensor.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR

19. INSPECT CRANKSHAFT POSITION SENSOR

  1. A072395E09
    Disconnect the B42 crankshaft position sensor connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B42-1 (NE) - B42-2 (NE-)
    Cold
    835 to 1,400 Ω
    B42-1 (NE) - B42-2 (NE-)
    Hot
    1,060 to 1,645 Ω

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensors. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR

20. INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

  1. A130311E01
    Disconnect the B60 fuel pressure sensor connector.

  1. Measure the resistance of each terminal of the fuel pressure sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    B60-2 (PR) - B60-1 (E2)
    16.4 kΩ or less
    B60-2 (PR) - B60-3 (VC)
    3 kΩ or less

  1. Reconnect the fuel pressure sensor connector.



NG
REPLACE COMMON RAIL ASSEMBLY
OK


21. CHECK WIRE HARNESS (FUEL PRESSURE SENSOR - ECM)

  1. A128588E04
    Disconnect the B60 fuel pressure sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B60-2 (PR) - B32-67 (PCR1)
    Below 1 Ω
    B60-3 (VC) - B32-69 (VCM)
    Below 1 Ω
    B60-1 (E2) - B32-91 (E2M)
    Below 1 Ω
    B60-2 (PR) or B32-67 (PCR1) - Body ground
    10 kΩ or higher
    B60-3 (VC) or B32-69 (VCM) - Body ground
    10 kΩ or higher
    B60-1 (E2) or B32-91 (E2M) - Body ground
    10 kΩ or higher

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


22. REPLACE ECM
  1. Replace the ECM.

    NOTICE:
    After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

  1. Check if the engine starts smoothly or if the engine stalls.

    OK:
    The engine starts smoothly and does not stall.



NG
REPLACE SUPPLY PUMP ASSEMBLY
OK

END


← Engine Difficult to Start or Stalling (Nov 2005 – Dec 2006)Black Smoke Emitted (Nov 2005 – Dec 2006) →