DISASSEMBLY
Removal / installation · Vehicles built Jan 2007 – Jul 2008
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008
- CAUTION:
- Wear protective gloves. Sharp areas on the seat frame (with adjuster) may injure your hands.
| 1.
REMOVE RECLINING POWER SEAT SWITCH KNOB |
 |
Using a screwdriver, detach the knob.
- HINT:
- Tape the screwdriver tip before use.
| 2.
REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
 |
Using a screwdriver, detach the knob.
- HINT:
- Tape the screwdriver tip before use.
| 3.
REMOVE FRONT SEAT CUSHION SHIELD LH |
 |
- Disconnect the 2 rubber bands of the front seatback board from the front seat frame (with adjuster).
- Remove the 5 screws.
Using a screwdriver, detach the 3 claws and remove the cushion shield (with front No. 1 seat cushion inner shield).
- HINT:
- Tape the screwdriver tip before use.
Disconnect the connector from the front power seat lumbar switch.
- Remove the front No. 1 seat cushion inner shield from the cushion shield.
Remove the screw.
Using a screwdriver, detach the claw and remove the inner shield.
- HINT:
- Tape the screwdriver tip before use.
| 4.
REMOVE FRONT POWER SEAT LUMBAR SWITCH |
 |
- Remove the 2 screws and switch.
| 5.
REMOVE FRONT SEAT CUSHION INNER SHIELD LH |
 |
- Remove the screw.
Using a screwdriver, detach the 3 claws.
- HINT:
- Tape the screwdriver tip before use.
Using a clip remover, detach the clip and remove the inner shield.
| 6.
REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
|
 |
for Driver Seat:
Disconnect the 2 connectors and detach the 2 clamps.
for Passenger Seat:
Disconnect the connector and detach the 2 clamps.
- Remove the nut and seat belt.
| 7.
REMOVE FRONT POWER SEAT SWITCH |
 |
- Remove the 3 screws.
Disconnect the connector and remove the switch.
| 8.
REMOVE FRONT SEAT CUSHION COVER |
 |
w/ Seat Heater System:
Disconnect the connector.
- Using a clip remover, remove the 2 clips.
Detach the 2 hooks on the seat cushion front side.
Using a screwdriver, detach the hooks and remove the seat cushion cover (with pad).
- HINT:
- Tape the screwdriver tip before use.
- Remove the 15 hog rings and seat cushion cover from the seat cushion pad.
| 9.
REMOVE FRONT SEAT CUSHION HEATER (w/ Seat Heater System) |
 |
- Cut off the 10 tack pins which fasten the seat heater, and then remove the seat cushion heater from the seat cushion cover.
- NOTICE:
- Be careful not to damage the seat cushion cover and seat heater.
| 10.
REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH |
 |
- Open the lower part of the seatback board. Then remove the 2 screws.
- Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.
| 11.
REMOVE FRONT SEATBACK COVER |
 |
- Remove the 5 hog rings.
Using a screwdriver, detach the hooks.
- HINT:
- Tape the screwdriver tip before use.
- Detach the 4 claws and remove the 2 headrest supports.
- Remove the nut and move the 2 seatback cover brackets.
Remove the seatback cover (with pad) from the seat frame (with adjuster).
- Remove the 11 hog rings and seatback cover from the seatback pad.
| 12.
REMOVE FRONT SEATBACK HEATER (w/ Seat Heater System) |
 |
- Cut off the 6 tack pins which fasten the seat heater, and then remove the seat cushion heater from the seat cushion cover.
- NOTICE:
- Be careful not to damage the seat cushion cover and seat heater.
| 13.
REMOVE RECLINING ADJUSTER LOWER INSIDE COVER LH |
 |
Remove the 2 screws.
Detach the claw and remove the inside cover.
| 14.
REMOVE RECLINING ADJUSTER LOWER INSIDE COVER RH |
 |
- HINT:
- Use the same procedures described for the LH side.
| 15.
REMOVE RECLINING ADJUSTER UPPER INSIDE COVER LH |
 |
Remove the screw and inside cover.
| 16.
REMOVE RECLINING ADJUSTER UPPER INSIDE COVER RH |
 |
Remove the screw and inside cover.
| 17.
REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
 |
Remove the screw.
Detach the hook of the lower shield and remove the lower shield.
| 18.
REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
 |
- HINT:
- Use the same procedures described for the LH side.
| 19.
REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY |
 |
Disconnect the connector.
Remove the 2 screws and lumbar support adjuster.
| 20.
REMOVE SEAT POSITION AIRBAG SENSOR
|
 |
- Remove the seat slide position sensor protector from the seat position sensor.
Using a T30 "torx" socket, remove the "torx" screw and seat position sensor.
Disconnect the connector.
| 21.
REMOVE FRONT SEAT WIRE |
|