P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
Diagnostic trouble codes · Vehicles built from Nov 2005
DESCRIPTION
The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0705 |
When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic)
1. Either of the following is met (a) NSW(STAR) input signal is ON (b) P input signal is ON (c) N input signal is ON (d) R input signal is ON 2. Either of the following is met (a) 3 input signal is ON (b) L input signal is ON |
|
- HINT:
- *: Only for Euro-OBD vehicle
MONITOR DESCRIPTION
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is on P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on (IG) and turn the tester ON.
- Enter the following menus: Powertrain / Engine and ECT / Data List.
- Follow the instructions on the tester and read the Data List.
Item
Measurement Item/
Range (Display)
Normal Condition
Diagnostic Note
Neutral Position Switch Signal
PNP switch status/
ON or OFF
Shift lever is:
On P or N: ON
Not on P or N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (R range)
PNP switch status/
ON or OFF
Shift lever is:
On R: ON
Not on R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (P range)
PNP switch status/
ON or OFF
Shift lever is:
On P: ON
Not on P: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (N range)
PNP switch status/
ON or OFF
Shift lever is:
On N: ON
Not on N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (D range)
PNP switch status/
ON or OFF
Shift lever is:
On D: ON
Not on D: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (3 range)
PNP switch status/
ON or OFF
Shift lever is:
On 3: ON
Not on 3: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (2 range)
PNP switch status/
ON or OFF
Shift lever is:
On 2: ON
Not on 2: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (L range)
PNP switch status/
ON or OFF
Shift lever is:
On L: ON
Not on L: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
| 1. CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - BATTERY) |
![]() ![]() |
Disconnect the B28 park/neutral position switch connector.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester Connection
Specified Condition
2 (RB) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 2. CHECK WIRE HARNESS (OUTPUT SIGNAL) |
![]() ![]() |
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Specified Condition
4 (B) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 3. INSPECT PARK/NEUTRAL POSITION SWITCH |
Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

- Standard resistance:
Tester Connection
Shift Lever Position
Specified Condition
6 (PL) - 2 (RB)
P
Below 1 Ω
6 (PL) - 2 (RB)
Not on P
10 kΩ or higher
4 (B) - 5 (L)
P or N
Below 1 Ω
4 (B) - 5 (L)
Not on P or N
10 kΩ or higher
1 (RL) - 2 (RB)
R
Below 1 Ω
1 (RL) - 2 (RB)
Not on R
10 kΩ or higher
9 (NL) - 2 (RB)
N
Below 1 Ω
9 (NL) - 2 (RB)
Not on N
10 kΩ or higher
7 (DL) - 2 (RB)
D
Below 1 Ω
7 (DL) - 2 (RB)
Not on D
10 kΩ or higher
3 (2L) - 2 (RB)
2
Below 1 Ω
3 (2L) - 2 (RB)
Not on 2
10 kΩ or higher
8 (LL) - 2 (RB)
L
Below 1 Ω
8 (LL) - 2 (RB)
Not on L
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK WIRE HARNESS (ECM - PARK/NEUTRAL POSITION SWITCH) |
Connect the park/neutral position switch.
Disconnect the B32 ECM connector.

Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Shift Lever Position
Specified Condition
B32-73 (P) - Body ground
P
10 to 14 V
B32-73 (P) - Body ground
Not on P
Below 1 V
B32-53 (R) - Body ground
R
10 to 14 V*
B32-53 (R) - Body ground
Not on R
Below 1 V
B32-54 (N) - Body ground
N
10 to 14 V
B32-54 (N) - Body ground
Not on N
Below 1 V
B32-56 (D) - Body ground
D or 3
10 to 14 V
B32-56 (D) - Body ground
Not on D or 3
Below 1 V
B32-55 (2) - Body ground
2
10 to 14 V
B32-55 (2) - Body ground
Not on 2
Below 1 V
B32-74 (L) - Body ground
L
10 to 14 V
B32-74 (L) - Body ground
Not on L
Below 1 V
- HINT:
- *: The voltage will drop slightly due to the illumination of the back-up light.
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH) |
Disconnect the E45 switch connector.

Turn the ignition switch on (IG).
Measure the voltage when the shift lever is moved to each position.
- Standard voltage:
Tester Connection
Shift Lever Position
Specified Condition
1 (NSSD) - Body ground
D and 3
10 to 14 V
1 (NSSD) - Body ground
Not on D and 3
Below 1 V
|
|
||||
| OK | |
| 6. INSPECT TRANSMISSION CONTROL SWITCH |
Measure the resistance of the switch when the shift lever is moved to each position.

- Standard resistance:
Tester Connection
Shift Lever Position
Specified Condition
1 (NSSD) - 2 (AT3)
D
10 kΩ or higher
1 (NSSD) - 2 (AT3)
3
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (TRANSMISSION CONTROL SWITCH - ECM) |
Connect the E45 switch connector.
Disconnect the A12 ECM connector.

Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Shift Lever Position
Specified Condition
A12-26 (3) - Body ground
3
10 to 14 V
A12-26 (3) - Body ground
Not on 3
Below 1 V
- HINT:
- *: The voltage will drop slightly due to the illumination of the back-up light.
|
|
||||
| OK | ||
| ||
| 8. CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the B32 ECM connector.

Disconnect the B28 park/neutral position switch connector.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
B28-4 (B) - B32-52 (NSW(STAR))
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
B28-4 (B) or B32-52 (NSW(STAR)) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||


