P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
- P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)
- P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)
DESCRIPTION
- HINT:
- Although the DTC titles include oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
- Although the DTC titles include oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.


- HINT:
- When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
- The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the B+ side of the circuit.


- When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0031 P0051 |
Air-Fuel Ratio (A/F) sensor heater (bank 1 sensor 1) current is less than 0.8 A (1 trip detection logic) |
|
| P0032 P0052 |
Air-Fuel Ratio (A/F) sensor heater (bank 2 sensor 1) current is more than 10 A (1 trip detection logic) |
|
- HINT:
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that does not include cylinder No. 1.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
- Bank 1 refers to the bank that includes cylinder No. 1.
WIRING DIAGRAM
Refer to DTC P2195 (Click here)INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
| 1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Disconnect the A/F sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- Bank 1:
Tester Connection
Condition
Specified Condition
HA1A (1) - +B (2)
20°C (68°F)
1.8 to 3.4 Ω
HA1A (1) - A1A- (4)
Always
10 kΩ or higher
- Bank 2:
Tester Connection
Condition
Specified Condition
HA2A (1) - +B (2)
20°C (68°F)
1.8 to 3.4 Ω
HA2A (1) - A2A- (4)
Always
10 kΩ or higher
Reconnect the A/F sensor connector.
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
Disconnect the A/F sensor connector.

Turn the ignition switch to the ON position.
Measure the voltage between the terminal of the A/F sensor connector and body ground.
- Standard voltage:
Tester Connection
Specified Condition
+B (2) - Body ground
9 to 14 V
|
|
||||
| NG | |
| 3. INSPECT INTEGRATION RELAY (A/F RELAY) |
Remove the integration relay from the engine room No. 1 relay block.

Inspect the A/F relay.
Measure the A/F relay resistance.
- Standard resistance:
Tester Connection
Specified Condition
1C-1 - 1B-8
10 kΩ or higher
1C-1 - 1B-8
Below 1 Ω
(Apply battery voltage between terminals 1B-6 and 1B-7)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY) |
Disconnect the A/F sensor connector.

Remove the integration relay from the engine room No. 1 relay block.
Measure the resistance between the terminals.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
+B (2) - 1B-8
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
+B (2) or 1B-8 - Body ground
10 kΩ or higher
Reinstall the integration relay.
Reconnect the A/F sensor connector.
|
|
||||
| OK | ||
| ||
| 5. INSPECT FUSE (A/F) |
Remove the A/F fuse from the integration relay.

Measure the fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the A/F fuse.
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR |
Disconnect the A/F sensor connector.

Disconnect the ECM connector.
Measure the resistance between the terminals.
- Standard resistance (Check for open):
- Bank 1:
Tester Connection
Specified Condition
HA1A (B96-86) - HA1A (B7-1)
Below 1 Ω
- Bank 2:
Tester Connection
Specified Condition
HA2A (B96-109) - HA2A (B67-1)
Below 1 Ω
- Standard resistance (Check for short):
- Bank 1:
Tester Connection
Specified Condition
HA1A (B96-86) or HA1A (B7-1) - Body ground
10 kΩ or higher
- Bank 2:
Tester Connection
Specified Condition
HA2A (B96-109) or HA2A (B67-1) - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the A/F sensor connectors.
|
|
||||
| OK | |
| 7. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position
Turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
No output
A
P0031, P0032, P0051 and/or P0052
B
|
|
||||
| A | ||
| ||
