2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL OIL COOLER BRACKET

A123533E01
  1. Apply engine oil to 2 new O-rings.

    NOTICE:
    Do not apply engine oil to the O-ring labeled A.

  1. Install the 3 O-rings to the oil cooler bracket.

  1. A116610E01
    Install the oil cooler bracket with the 6 bolts and nut.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    36 mm (1.42 in.) for bolt A
    49 mm (1.93 in.) for except bolt A


2. INSTALL NO. 1 TURBO OIL PIPE

  1. A111251E01
    Install the oil pipe and 2 new gaskets with the 2 union bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    HINT:
    Be sure to install the union bolt A so that the gasket is positioned as shown in the illustration.


3. INSTALL NO. 3 WATER BY-PASS PIPE

  1. A111249
    Install a new O-ring and the by-pass pipe with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


4. INSTALL OIL COOLER ASSEMBLY

A123534E01
  1. Apply engine oil to 2 new O-rings.

    NOTICE:
    Do not apply engine oil to a new O-ring labeled A.

  1. Install the 3 O-rings to the oil cooler bracket.

  1. A115201
    Install the oil cooler with the 5 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the No. 1 water by-pass hose and position the 2 clips.

  1. Connect the oil pressure switch connector.


5. INSTALL DIESEL THROTTLE BODY

  1. A124890
    Install a new gasket and the diesel throttle body with the 2 nuts and 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the throttle position sensor connector.

  1. Connect the throttle motor connector.


6. INSTALL OIL DIPSTICK GUIDE
  1. Apply engine oil to a new O-ring.

  1. Install the O-ring to the dipstick guide.

  1. A116265
    Install the oil dipstick guide with the 2 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Install the oil dipstick.


7. INSTALL NO. 2 AIR HOSE

8. INSTALL NO. 2 AIR TUBE

9. CONNECT ENGINE WIRE

A129528
  1. Connect the engine wire to the wire bracket with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the engine wire to the engine cover bracket with the bolt and 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the pressure sensor connector and 2 clamps.

  1. Connect the common rail connector.

  1. Connect the glow plug wire harness with the nut and grommet.

    Torque:
    2.2 N*m{ 22 kgf*cm , 19 in.*lbf }

  1. Connect the 4 injector connectors and install the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


10. INSTALL NO. 1 AIR TUBE

  1. A124905
    Install the No.1 air tube with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. Tighten the 2 clamps.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

  1. A124904
    Install the wire harness with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


11. INSTALL AIR CLEANER BRACKET

  1. A124934
    Install the bracket with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 fuel hoses to the bracket.

  1. Connect the 2 wire harness clamps.

  1. A124933
    Install the glow plug relay and connect the fuel filter level switch connector.


12. CONNECT FUEL FILTER ASSEMBLY
  1. Install the fuel filter with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 4 hoses.

  1. Connect the level warning switch connector.

    A125342


13. INSTALL AIR CLEANER CASE ASSEMBLY

  1. A129328
    Install the air cleaner case with the 3 bolts and connect the wire harness clamp.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element.


14. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A124929E02
    Insert the hinge parts of the air cleaner cap into the air cleaner case, and then hang the 3 hook clamps.

  1. Connect the mass air flow meter connector.

  1. Connect the wire harness clamp.


15. INSTALL BATTERY BRACKET REINFORCEMENT

  1. A124919
    Install the bracket reinforcement with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


16. INSTALL FRONT BATTERY BRACKET

  1. A124918
    Install the front bracket with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Attach the 2 wire harness clamps.


17. INSTALL BATTERY

18. INSTALL BATTERY CLAMP SUB-ASSEMBLY

  1. A124917E01
    Attach the hook of the battery clamp to the front battery bracket.

  1. Temporarily tighten the nut and install the bolt.

  1. Adjust the battery clamp's position.

  1. Fully tighten the nut and bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the 2 wire harness clamps.


19. INSTALL RADIATOR SUPPORT OPENING COVER

  1. B130259
    Install the 2 clips.


20. INSTALL NO. 2 AIR TUBE

21. INSTALL NO. 1 ENGINE COVER

  1. A123518
    Attach the 4 clips to install the engine cover.


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

23. ADD ENGINE OIL
  1. Wipe the oil pan and drain plug before installing the plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. A123522
    Close the oil pan drain service cover and install the clip.

  1. Add new oil.

    Standard oil capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    5.9 liters ( 6.2 US qts, 5.2 Imp. qts)
    Drain and refill without oil filter change
    5.5 liters ( 5.8 US qts, 4.8 Imp. qts)
    Dry fill
    6.7 liters ( 7.1 US qts, 5.9 Imp. qts)

  1. Install the oil filler cap.


24. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

  1. A126841E01
    Continue adding TOYOTA SLLC until it is filled to the B line.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard capacity:
    Item
    Specified Condition
    w/o Combustion Type Power Heater
    7.3 liters
    (7.7 US qts, 6.4 Imp. qts)
    w/ Combustion Type Power Heater
    7.7 liters
    (8.1 US qts, 6.8 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine, and warm it up until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Specified Condition
      Manual Air Conditioning System
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Automatic Air Conditioning System
      Temperature - Toward MAX
      Air conditioning switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Until the coolant level has stabilized, run the engine at 2,000 rpm.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

  1. A126840
    Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.


25. CHECK FOR ENGINE COOLANT LEAKS
  1. Remove the radiator reservoir cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A128571E01
    Fill the radiator with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 137 kPa (1.4 kgf/cm2, 19 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.


26. CHECK FOR ENGINE OIL LEAKS
  1. Start the engine. Make sure that no oil leaks from the connection point of the oil filter cap assembly.


27. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the engine under cover with the 12 clips and 4 bolts.

← INSTALLATION (Jan 2007 – Jul 2007)ON-VEHICLE INSPECTION (from Nov 2005) →