INSTALLATION
Removal / installation · Vehicles built from Aug 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1. INSTALL OIL COOLER BRACKET |
Apply a light coat of engine oil to 2 new O-rings.

- NOTICE:
- Do not apply engine oil to a new O-ring labeled A.
Install the 3 O-rings to the oil cooler bracket.
Install the oil cooler bracket with the 6 bolts and nut.

- Torque:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
- HINT:
- Each bolt length is indicated below.
- Bolt length:
- 36 mm (1.42 in.) for bolt A
- 49 mm (1.93 in.) for except bolt A
| 2. INSTALL NO. 1 TURBO OIL PIPE |
Install the oil pipe and 2 new gaskets with the 2 union bolts.

- Torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
- HINT:
- Be sure to install the union bolt A so that the gasket is positioned as shown in the illustration.
| 3. INSTALL NO. 3 WATER BY-PASS PIPE |
Install a new O-ring and the by-pass pipe with the 2 bolts.

- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
| 4. INSTALL OIL COOLER ASSEMBLY |
Apply a light coat of engine oil to 2 new O-rings.

- NOTICE:
- Do not apply engine oil to the O-ring labeled A.
Install the 3 O-rings to the oil cooler bracket.
Install the oil cooler with the 5 bolts.

- Torque:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Install the No. 1 water by-pass hose and position the 2 clips.
Connect the oil pressure switch connector.
| 5. INSTALL DIESEL THROTTLE BODY |
Install a new gasket and the diesel throttle body with the 2 nuts and 2 bolts.

- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Connect the throttle position sensor connector.
Connect the throttle motor connector.
| 6. INSTALL OIL DIPSTICK GUIDE |
Apply engine oil to a new O-ring.
Install the O-ring to the dipstick guide.
Install the oil dipstick guide with the 2 bolts.

- Torque:
- 33 N*m{ 337 kgf*cm , 24 ft.*lbf }
Install the oil dipstick.
| 7. CONNECT ENGINE WIRE |
Connect the engine wire to the wire bracket with the nut.

- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Connect the engine wire to the engine cover bracket with the bolt and 2 nuts.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Connect the pressure sensor connector and 2 clamps.
Connect the common rail connector.
Connect the glow plug wire harness with the nut and grommet.
- Torque:
- 2.2 N*m{ 22 kgf*cm , 19 in.*lbf }
Connect the 4 injector connectors and install the 2 nuts.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
| 8. INSTALL NO. 1 AIR TUBE |
Install the No.1 air tube with the 2 bolts.

- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
Tighten the 2 clamps.
- Torque:
- 6.3 N*m{ 64 kgf*cm , 56 in.*lbf }
Install the wire harness with the 2 bolts.

- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
| 9. INSTALL AIR CLEANER BRACKET |
Install the bracket with the 3 bolts.

- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Connect the 2 fuel hoses to the bracket.
Connect the 2 wire harness clamps.
Install the glow plug relay and connect the fuel filter level switch connector.

| 10. CONNECT FUEL FILTER ASSEMBLY |
Install the fuel filter assembly with the bolt.

- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
| 11. INSTALL AIR CLEANER CASE ASSEMBLY |
Install the air cleaner case with the 3 bolts and connect the wire harness clamp.

- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Install the air cleaner element.
| 12. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Insert the hinge parts of the air cleaner cap into the air cleaner case, and then hang the 3 hook clamps.

Connect the mass air flow meter connector.
Connect the wire harness clamp.
| 13. INSTALL BATTERY BRACKET REINFORCEMENT |
Install the bracket reinforcement with the 2 bolts.

- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
| 14. INSTALL FRONT BATTERY BRACKET |
Install the front bracket with the 4 bolts.

- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Attach the 2 wire harness clamps.
| 15. INSTALL BATTERY |
| 16. INSTALL BATTERY CLAMP SUB-ASSEMBLY |
Attach the hook of the battery clamp to the front battery bracket.

Temporarily tighten the nut and install the bolt.
Adjust the battery clamp's position.
Fully tighten the nut and bolt.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Attach the 2 wire harness clamps.
| 17. INSTALL RADIATOR SUPPORT OPENING COVER |
Install the cover with the 9 clips.
| 18. INSTALL NO. 2 AIR TUBE |
- NOTICE:
- When reusing the air hose or air tube, check that there is no damage and foreign objects. If necessary, clean it.
Align the intercooler with the radiator, and then install the intercooler to the radiator with the 4 bolts.

- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
Install the No. 2 air tube to the intercooler and No. 3 air hose.
Install the bolt.
- Torque:
- 31 N*m{ 316 kgf*cm , 23 ft.*lbf }
Tighten the 2 clamps as shown in the illustration.

Install the No. 2 air hose to the intercooler. Tighten the clamp as shown in the illustration.

Install the radiator (with intercooler) to the vehicle.
Connect the No. 2 and No. 3 air hoses to the engine.
Tighten the 2 clamps as shown in the illustration.

| 19. INSTALL NO. 1 ENGINE COVER |
Attach the 4 clips to install the engine cover.

| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. ADD ENGINE OIL |
Wipe the oil pan and drain plug before installing the plug.
Install a new gasket and the oil pan drain plug.
- Torque:
- 38 N*m{ 387 kgf*cm , 28 ft.*lbf }
Close the oil pan drain service cover and install the clip.

Add new oil.
- Standard oil capacity:
Item
Specified Condition
Drain and refill with oil filter change
5.9 liters ( 6.2 US qts, 5.2 Imp. qts)
Drain and refill without oil filter change
5.5 liters ( 5.8 US qts, 4.8 Imp. qts)
Dry fill
6.7 liters ( 7.1 US qts, 5.9 Imp. qts)
Install the oil filler cap.
| 22. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
- Torque:
- 12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.
Continue adding TOYOTA SLLC until it is filled to the B line.

- HINT:
- The B line is the lower edge of the inner wall of the filler neck.
- Standard capacity:
Item
Specified Condition
w/o Combustion Type Power Heater
7.3 liters
(7.7 US qts, 6.4 Imp. qts)
w/ Combustion Type Power Heater
7.7 liters
(8.1 US qts, 6.8 Imp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- NOTICE:
- Never use water as a substitute for engine coolant.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine, and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
Item
Specified Condition
Manual Air Conditioning System
Fan speed - Any setting except "OFF"
Temperature - Toward WARM
Air conditioning switch "OFF"
Automatic Air Conditioning System
Temperature - Toward MAX
Air conditioning switch "OFF"
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
- NOTICE:
- Make sure that the radiator reservoir still has some coolant in it.
- Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
- If there is not enough coolant, the engine may burn out or overheat.
- Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
- Until the coolant level has stabilized, run the engine at 2,000 rpm.
- Make sure that the radiator reservoir still has some coolant in it.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Wear protective gloves.
Stop the engine and wait until the coolant cools down to ambient temperature.
Check that the coolant level is between the FULL and LOW line.

If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.
| 23. CHECK FOR ENGINE COOLANT LEAKS |
Remove the radiator reservoir cap.
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.
Fill the radiator with coolant, and then attach a radiator cap tester.

Warm up the engine.
Pump the radiator cap tester to 137 kPa (1.4 kgf/cm2, 19 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator cap.
| 24. CHECK FOR ENGINE OIL LEAKS |
Start the engine. Make sure that no oil leaks from the connection point of the oil filter cap assembly.
| 25. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 4 bolts and 12 clips.
