1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2.
REMOVE NO. 1 ENGINE UNDER COVER
Remove the 4 bolts, 12 clips and under cover.
3.
DRAIN ENGINE COOLANT
Loosen the radiator drain cock plug.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Remove the radiator reservoir cap.
CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Loosen the cylinder block drain cock plug.
4.
DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the clip and open the oil pan drain service cover.
Remove the oil drain plug and gasket, and drain the engine oil into a container.
5.
REMOVE NO. 2 AIR TUBE
Loosen the 2 clamps.
Disconnect the No. 2 and No. 3 air hoses from the engine.
Remove the radiator (with intercooler) from the vehicle.
Loosen the 2 clamps.
Remove the bolt.
Remove the No. 2 air tube from the intercooler and No. 3 air hose.
Loosen the clamp. Remove the No. 2 air hose from the intercooler.
Remove the 4 bolts, and then separate the intercooler and radiator.
6.
REMOVE NO. 1 ENGINE COVER
Detach the 4 clips and remove the engine cover.
7.
REMOVE RADIATOR SUPPORT OPENING COVER
Remove the 9 clips and cover.
8.
REMOVE BATTERY CLAMP SUB-ASSEMBLY
Remove the bolt and loosen the nut.
Detach the 2 wire harness clamps.
Detach the hook of the battery clamp from the battery bracket front, and then remove the battery clamp.
9.
REMOVE BATTERY
10.
REMOVE FRONT BATTERY BRACKET
Detach the 2 wire harness clamps.
Remove the 4 bolts and bracket front.
11.
REMOVE BATTERY BRACKET REINFORCEMENT
Remove the 2 bolts and bracket reinforcement.
12.
REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Disconnect the mass air flow meter connector.
Disconnect the wire harness clamp.
Unhook the 3 hook clamps, and then remove the air cleaner cap.
Remove the air cleaner element from the air cleaner case.
13.
REMOVE AIR CLEANER CASE ASSEMBLY
Disconnect the wire harness clamp and remove the 3 bolts and air cleaner case.
14.
DISCONNECT FUEL FILTER ASSEMBLY
Remove the bolt and fuel filter assembly.
15.
REMOVE AIR CLEANER BRACKET
Remove the glow plug relay.
Disconnect the fuel filter level switch connector.
Disconnect the 2 wire harness clamps.
Disconnect the 2 fuel hoses from the bracket.
Remove the 3 bolts and bracket.
16.
REMOVE NO. 1 AIR TUBE
Remove the 2 bolts and disconnect the wire harness.
Remove the 2 bolts and loosen the 2 clamps.
Remove the No. 1 air tube.
17.
DISCONNECT ENGINE WIRE
Disconnect the 4 injector connectors and 2 nuts.
Remove the grommet and nut and disconnect the glow plug wire harness.
Disconnect the common rail connector.
Disconnect the pressure sensor connector and 2 clamps.
Remove the bolt, 2 nuts and disconnect the engine wire from the engine cover bracket.
Remove the nut and disconnect the engine wire from the wire bracket.
18.
REMOVE OIL DIPSTICK GUIDE
Remove the oil dipstick.
Remove the 2 bolts, oil dipstick guide and O-ring.
19.
REMOVE DIESEL THROTTLE BODY
Disconnect the throttle position sensor connector.
Disconnect the throttle motor connector.
Remove the 2 nuts and 2 bolts, and then remove the diesel throttle body and gasket.
20.
REMOVE OIL COOLER ASSEMBLY
Disconnect the oil pressure switch connector.
Loosen the 2 clips and disconnect the No. 1 water by-pass hose.