2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO. 1 ENGINE UNDER COVER

3. DRAIN ENGINE COOLANT
  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the cylinder block drain cock plug.

    A126839E01


4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A123522
    Remove the clip and open the oil pan drain service cover.

  1. A123521
    Remove the oil drain plug and gasket, and drain the engine oil into a container.


5. REMOVE NO. 2 AIR TUBE

6. REMOVE NO. 1 ENGINE COVER

  1. A123518
    Detach the 4 clips and remove the engine cover.


7. REMOVE RADIATOR SUPPORT OPENING COVER

  1. B130259
    Remove the 2 clips.

  1. Partially remove the radiator support opening cover.

    HINT:
    It is not necessary to fully remove the radiator support opening cover. Partially remove it so that the bumper cover can be removed later.


8. REMOVE BATTERY CLAMP SUB-ASSEMBLY

A124917E01
  1. Remove the bolt and loosen the nut.

  1. Detach the 2 wire harness clamps.

  1. Detach the hook of the battery clamp from the front battery bracket , and then remove the battery clamp.


9. REMOVE BATTERY

10. REMOVE FRONT BATTERY BRACKET

  1. A124918
    Detach the 2 wire harness clamps.

  1. Remove the 4 bolts and front bracket.


11. REMOVE BATTERY BRACKET REINFORCEMENT

  1. A124919
    Remove the 2 bolts and bracket reinforcement.


12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A124927E01
    Disconnect the mass air flow meter connector.

  1. Disconnect the wire harness clamp.

  1. Unhook the 3 hook clamps, and then remove the air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


13. REMOVE AIR CLEANER CASE ASSEMBLY

  1. A124928E01
    Disconnect the wire harness clamp and remove the 3 bolts and air cleaner case.


14. DISCONNECT FUEL FILTER ASSEMBLY
  1. Disconnect the level warning switch connector.

  1. Disconnect the 4 hoses indicated in the illustration.

  1. Remove the bolt and fuel filter.

    A125342


15. REMOVE AIR CLEANER BRACKET

  1. A124933
    Remove the glow plug relay.

  1. Disconnect the fuel filter level switch connector.

  1. A124934
    Disconnect the 2 wire harness clamps.

  1. Disconnect the 2 fuel hoses from the bracket.

  1. Remove the 3 bolts and bracket.


16. REMOVE NO. 1 AIR TUBE

  1. A124904
    Remove the 2 bolts and disconnect the wire harness.

  1. A124905
    Remove the 2 bolts and loosen the 2 clamps.

  1. Remove the No. 1 air tube.


17. DISCONNECT ENGINE WIRE

A129528
  1. Disconnect the 4 injector connectors and 2 nuts.

  1. Remove the grommet and nut and disconnect the glow plug wire harness.

  1. Disconnect the common rail connector.

  1. Disconnect the pressure sensor connector and 2 clamps.

  1. Remove the bolt, 2 nuts and disconnect the engine wire from the engine cover bracket.

  1. Remove the nut and disconnect the engine wire from the wire bracket.


18. REMOVE OIL DIPSTICK GUIDE
  1. Remove the oil dipstick.

  1. A116265
    Remove the 2 bolts, oil dipstick guide and O-ring.


19. REMOVE DIESEL THROTTLE BODY

  1. A124890
    Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 nuts and 2 bolts, and then remove the diesel throttle body and gasket.


20. REMOVE OIL COOLER ASSEMBLY
  1. Disconnect the oil pressure switch connector.

  1. Loosen the 2 clips and disconnect the No. 1 water by-pass hose.

  1. A117779
    Remove the 5 bolts and engine oil cooler.

  1. Remove the 3 O-rings.


21. REMOVE NO. 3 WATER BY-PASS PIPE

  1. A123609
    Remove the 2 bolts, O-ring and by-pass pipe.


22. REMOVE NO. 1 TURBO OIL PIPE

  1. A111250
    Remove the 2 union bolts, 2 gaskets and oil pipe.


23. REMOVE OIL COOLER BRACKET

  1. A111252E05
    Remove the 6 bolts, nut and oil cooler bracket.

  1. Remove the 3 O-rings.

← REMOVAL (Nov 2005 – Dec 2006)REMOVAL (from Aug 2007) →