P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.- HINT:
- The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC No. |
DTC Detection condition |
Trouble Area |
| P504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch on (IG) (b) Brake pedal released (c) STP signal OFF when ST1- signal OFF |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- STP signal conditions can be checked using the intelligent tester.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on (IG) and turn the tester ON.
- Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
- Check the STP signal when the brake pedal is depressed and released.
Brake Pedal Operation
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
![]() ![]() |
Disconnect the A5 stop light switch connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals of the A5 stop light switch connector and body ground.
- Standard voltage:
Tester Connections
Specified Conditions
B (A5-2) - Body ground
9 to 14 V
B (A5-3) - Body ground
9 to 14 V
Reconnect the stop light switch connector.
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the stop light switch assembly.
Measure the resistance.
- Standard resistance:
Tester Connection
Switch Position
Specified Condition
1 - 2
Switch pin not pushed
Below 1 Ω
Switch pin pushed
10 kΩ or higher
3 - 4
Switch pin not pushed
10 kΩ or higher
Switch pin pushed
Below 1 Ω
Reinstall the stop light switch assembly.
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1 - VOLTAGE) |
![]() ![]() |
Disconnect the A12 ECM connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals ST1- and STP of the A12 ECM connector and body ground.
- Standard voltage:
Tester Connection
Brake Pedal Operation
Specified Condition
ST1- (A12-35) - Body ground
Released
9 to 14 V
Depressed
0 to 3 V
STP (A12-36) - Body ground
Released
0 to 3 V
Depressed
9 to 14 V
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (STOP AND IGN FUSE) |
![]() ![]() |
Remove the STOP and IGN fuses from the main body ECU (instrument panel junction block).
Measure the resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the STOP and IGN fuses.
|
|
||||
| OK | ||
| ||




