2005-2008 RAV4 · Service Manual ENGINE

TERMINALS OF ECU

System information · Vehicles built from Nov 2005


CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
E114510E18
E123909E04
  1. Disconnect the IB, ID, IE, E18 and E19 junction block connectors.

  2. Measure the voltages and resistances of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BECU (IB-30) - Body ground
    R - Body ground
    +B power supply
    Always
    10 to 14 V
    AM1 (E19-1) - Body ground
    W - Body ground
    +B power supply
    Always
    10 to 14 V
    AM2 (E18-6) - Body ground
    W - Body ground
    +B power supply
    Always
    10 to 14 V
    SSW1 (E19-10) - Body ground
    W - Body ground
    Ignition switch signal
    Ignition switch pushed
    Below 1 Ω
    SSW1 (E19-10) - Body ground
    W - Body ground
    Ignition switch signal
    Ignition switch not pushed
    10 kΩ or higher
    SSW2 (E19-9) - Body ground
    B - Body ground
    Ignition switch signal
    Ignition switch pushed
    Below 1 Ω
    SSW2 (E19-9) - Body ground
    B - Body ground
    Ignition switch signal
    Ignition switch not pushed
    10 kΩ or higher
    GND1 (IE-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND2 (E19-4) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    LIN1 (ID-9) - Body ground
    V - Body ground
    LIN line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the IB, ID, IE, E18 and E19 junction block connectors.

  4. Measure the voltages of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ACCD (E18-4) - GND2 (E19-4)
    R - W-B
    ACC signal
    Ignition switch on (ACC)
    10 to 14 V
    ACCD (E18-4) - GND2 (E19-4)
    R - W-B
    ACC signal
    Ignition switch off
    Below 1 V
    IG2D (E19-5) - GND2 (E19-4)
    W - W-B
    IG2 signal
    Ignition switch on (IG)
    10 to 14 V
    IG2D (E19-5) - GND2 (E19-4)
    W - W-B
    IG2 signal
    Ignition switch on (ACC)
    Below 1 V
    SLR+ (E18-7) - GND2 (E19-4)
    Y - W-B
    Steering lock motor signal
    Steering lock motor operating
    Below 1 V
    SLR+ (E18-7) - GND2 (E19-4)
    Y - W-B
    Steering lock motor signal
    Steering lock motor does not operate
    10 to 14 V
    SLP (E18-18) - GND2 (E19-4)
    G - W-B
    Steering lock actuator position signal
    Steering lock locked
    10 to 14 V
    SLP (E18-18) - GND2 (E19-4)
    G - W-B
    Steering lock actuator position signal
    Steering lock released
    Below 1 V
    SPD (IC-8) - GND2 (E19-4)
    V - W-B
    Speed signal from combination meter
    Ignition switch on (IG), Rotate driving wheel slowly
    Pulse generation
    (see waveform 1)
    TACH (E20-2) - GND2 (E19-4)
    GR - W-B
    Tachometer signal
    Engine running
    Pulse generation
    (see waveform 2)
    STSW (E20-4) - GND2 (E19-4)
    R - W-B
    Starter activation request signal
    Clutch pedal depressed, ignition switch pushed once
    10 to 14 V*
    STR (E20-3) - GND2 (E19-4)
    W - W-B
    Clutch pedal switch
    Clutch pedal depressed
    Below 1 V
    STR2 (E20-14) - GND2 (E19-4)
    W - W-B
    Starter signal
    Clutch pedal depressed, ignition switch pushed once
    10 to 14 V*
    INDS (E20-1) - GND2 (E19-4)
    R - W-B
    Vehicle condition signal
    Clutch pedal depressed, ignition switch off, on (ACC, IG)
    10 to 14 V
    INDW (E20-8) - GND2 (E19-4)
    Y - W-B
    Vehicle condition signal
    Clutch pedal released, ignition switch off, on (ACC, IG)
    10 to 14 V
    SWIL (E19-8) - GND2 (E19-4)
    G - W-B
    Illumination signal
    Light control switch TAIL or HEAD
    10 to 14 V

    HINT:
    *: Voltage is output for 0.3 seconds before the engine is started.

    If the result is not as specified, the ECU may have a malfunction.

  5. I042329E04
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    SPD (IC-8) - GND2 (E19-4)
    Tool Setting
    5 V/DIV., 10 msec./DIV.
    Condition
    Driving at approx. 20 km/h (12 mph)

    HINT:
    As the vehicle speed increases, the wavelength shortens.

  6. I042330E10
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Symbols (Terminal No.)
    TACH (E20-2) - GND2 (E19-4)
    Tool Setting
    5 V/DIV., 10 msec./DIV.
    Condition
    Engine idling

    HINT:
    As the vehicle speed increases, the wavelength shortens.


CHECK CERTIFICATION ECU
B108931E05
  1. Disconnect the E63 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B1 (E63-1) - Body ground
    R - Body ground
    +B power supply
    Always
    10 to 14 V
    IG (E63-18) - Body ground
    B - Body ground
    Ignition power supply
    Ignition switch on (IG)
    10 to 14 V
    IG (E63-18) - Body ground
    B - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    LIN (E63-10) - Body ground
    V - Body ground
    LIN line
    Always
    10 kΩ or higher
    E (E63-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM
C128047E02
  1. Disconnect the A12 and B32 ECM connectors.

  2. Measure the voltages and resistances of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BATT (A12-2) - E1 (B32-109)
    W - BR
    Battery (for measuring battery voltage and for ECM memory)
    Always
    10 to 14 V
    +B (A12-1) - E1 (B32-109)
    B - BR
    Power source of ECM
    Ignition switch on (IG)
    10 to 14 V
    IGSW (A12-25) - E1 (B32-109)
    B - BR
    Ignition switch signal
    Ignition switch on (IG)
    10 to 14 V
    E1 (B32-109) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E02 (B32-44) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E05 (B32-46) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E01 (B32-45) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the A12 and B32 ECM connectors.

  4. Measure the voltage of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    STA (A12-43) - E1 (B32-109)
    LG - BR
    Starter relay operation signal
    Cranking
    5.5 V or more
    ACCR (A12-24) - E1 (B32-109)
    LG - BR
    ACC relay cut signal (output)
    Ignition switch on (IG) → Cranking
    10 to 14 V → Below 1 V
    TACH (A12-13) - E1 (B32-109)
    GR - BR
    Engine revolution signal (output)
    Idling
    Pulse generation
    (see waveform 1)
    STAR (B32-53) - E1 (B32-109)
    W - BR
    Starter relay drive signal
    Cranking
    10 to 14 V
    If the result is not as specified, the ECM may have a malfunction.

  5. Inspect the connector using an oscilloscope.

    1. I042330E01
      Waveform 1
      Item
      Content
      Symbols (Terminal No.)
      TACH (A12-13) - E1 (B32-109)
      Tool Setting
      5 V/DIV., 10 msec./DIV.
      Condition
      Engine idling

      HINT:
      As the vehicle speed increases, the wavelength shortens.


CHECK STEERING LOCK ECU
B106649E11
  1. Disconnect the E6 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B (E6-7) - Body ground
    L - Body ground
    +B power supply
    Always
    Always
    IG2 (E6-6) - Body ground
    B - Body ground
    Ignition power supply
    Ignition switch on (IG)
    Always
    IG2 (E6-6) - Body ground
    B - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    GND (E6-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    SGND (E6-2) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E6 ECU connector.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SLP1 (E6-4) - GND (E6-1)
    G - W-B
    Steering lock actuator position signal
    Steering lock locked
    10 to 14 V
    SLP1 (E6-4) - GND (E6-1)
    G - W-B
    Steering lock actuator position signal
    Steering lock released
    Below 1 V
    1. If the result is not as specified, the ECU may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jan 2007)DIAGNOSIS SYSTEM (from Nov 2005) →