TERMINALS OF ECU
System information · Vehicles built from Nov 2005
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |




Disconnect the IB, ID, IE, E18 and E19 junction block connectors.
Measure the voltages and resistances of the wire harness side connectors.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BECU (IB-30) - Body ground
R - Body ground
+B power supply
Always
10 to 14 V
AM1 (E19-1) - Body ground
W - Body ground
+B power supply
Always
10 to 14 V
AM2 (E18-6) - Body ground
W - Body ground
+B power supply
Always
10 to 14 V
SSW1 (E19-10) - Body ground
W - Body ground
Ignition switch signal
Ignition switch pushed
Below 1 Ω
SSW1 (E19-10) - Body ground
W - Body ground
Ignition switch signal
Ignition switch not pushed
10 kΩ or higher
SSW2 (E19-9) - Body ground
B - Body ground
Ignition switch signal
Ignition switch pushed
Below 1 Ω
SSW2 (E19-9) - Body ground
B - Body ground
Ignition switch signal
Ignition switch not pushed
10 kΩ or higher
GND1 (IE-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
GND2 (E19-4) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
LIN1 (ID-9) - Body ground
V - Body ground
LIN line
Always
10 kΩ or higher
Reconnect the IB, ID, IE, E18 and E19 junction block connectors.
Measure the voltages of the connectors.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
ACCD (E18-4) - GND2 (E19-4)
R - W-B
ACC signal
Ignition switch on (ACC)
10 to 14 V
ACCD (E18-4) - GND2 (E19-4)
R - W-B
ACC signal
Ignition switch off
Below 1 V
IG2D (E19-5) - GND2 (E19-4)
W - W-B
IG2 signal
Ignition switch on (IG)
10 to 14 V
IG2D (E19-5) - GND2 (E19-4)
W - W-B
IG2 signal
Ignition switch on (ACC)
Below 1 V
SLR+ (E18-7) - GND2 (E19-4)
Y - W-B
Steering lock motor signal
Steering lock motor operating
Below 1 V
SLR+ (E18-7) - GND2 (E19-4)
Y - W-B
Steering lock motor signal
Steering lock motor does not operate
10 to 14 V
SLP (E18-18) - GND2 (E19-4)
G - W-B
Steering lock actuator position signal
Steering lock locked
10 to 14 V
SLP (E18-18) - GND2 (E19-4)
G - W-B
Steering lock actuator position signal
Steering lock released
Below 1 V
SPD (IC-8) - GND2 (E19-4)
V - W-B
Speed signal from combination meter
Ignition switch on (IG), Rotate driving wheel slowly
Pulse generation
(see waveform 1)
TACH (E20-2) - GND2 (E19-4)
GR - W-B
Tachometer signal
Engine running
Pulse generation
(see waveform 2)
STSW (E20-4) - GND2 (E19-4)
R - W-B
Starter activation request signal
Clutch pedal (M/T) or brake pedal (A/T) with shift lever in P or N depressed, ignition switch pushed once
10 to 14 V*
STR (E20-3) - GND2 (E19-4)
W - W-B
Clutch start switch (M/T)
Park / neutral position switch (A/T)
Clutch pedal depressed (M/T)
Shift lever in P or N (A/T)
Below 1 V
STR2 (E20-14) - GND2 (E19-4)
W - W-B
Starter signal
Clutch pedal (M/T) or brake pedal (A/T) with shift lever in P or N depressed, ignition switch pushed once
10 to 14 V*
INDS (E20-1) - GND2 (E19-4)
R - W-B
Vehicle condition signal
Clutch pedal (M/T) or brake pedal (A/T) with shift lever in P or N depressed, ignition switch off, on (ACC, IG)
10 to 14 V
INDW (E20-8) - GND2 (E19-4)
Y - W-B
Vehicle condition signal
Clutch pedal (M/T) or brake pedal (A/T) with shift lever in P or N released, ignition switch off, on (ACC, IG)
10 to 14 V
SWIL (E19-8) - GND2 (E19-4)
G - W-B
Illumination signal
Light control switch TAIL or HEAD
10 to 14 V
STP (E18-14) - GND2 (E19-4)
L - W-B
Stop light switch signal
Brake pedal depressed
10 to 14 V
- HINT:
- *: Voltage is output for 0.3 seconds before the engine is started.
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Symbols (Terminal No.)
SPD (IC-8) - GND2 (E19-4)
Tool Setting
5 V/DIV., 10 msec./DIV.
Condition
Driving at approx. 20 km/h (12 mph)
- HINT:
- As the vehicle speed increases, the wavelength shortens.
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Symbols (Terminal No.)
TACH (E20-2) - GND2 (E19-4)
Tool Setting
5 V/DIV., 10 msec./DIV.
Condition
Engine idling
- HINT:
- As the vehicle speed increases, the wavelength shortens.
| CHECK CERTIFICATION ECU |


Disconnect the E63 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
+B1 (E63-1) - Body ground
R - Body ground
+B power supply
Always
10 to 14 V
IG (E63-18) - Body ground
B - Body ground
Ignition power supply
Ignition switch on (IG)
10 to 14 V
IG (E63-18) - Body ground
B - Body ground
Ignition power supply
Ignition switch off
Below 1 V
LIN (E63-10) - Body ground
V - Body ground
LIN line
Always
10 kΩ or higher
E (E63-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
| CHECK ECM |


Disconnect the A12 and B32 ECM connectors.
Measure the voltages and resistances of the wire harness side connectors.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BATT (A12-20) - E1 (B32-104)
W - BR
Battery (for measuring battery voltage and for ECM memory)
Always
10 to 14 V
+B (A12-2) - E1 (B32-104)
B - BR
Power source of ECM
Ignition switch on (IG)
10 to 14 V
+B2 (A12-1) - E1 (B32-104)
B - BR
Power source of ECM
Ignition switch on (IG)
10 to 14 V
IGSW (A12-28) - E1 (B32-104)
B - BR
Ignition switch signal
Ignition switch on (IG)
10 to 14 V
E1 (B32-104) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
E02 (B32-44) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E04 (B32-46) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E01 (B32-45) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the A12 and B32 ECM connectors.
Measure the voltage of the connectors.
If the result is not as specified, the ECM may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
STA (A12-48) - E1 (B32-104)
LG - BR
Starter relay operation signal
Cranking
5.5 V or more
ACCR (A12-13) - E1 (B32-104)
LG - BR
ACC relay cut signal (output)
Ignition switch on (IG) → Cranking
10 to 14 V → Below 1 V
TACH (A12-15) - E1 (B32-104)
GR - BR
Engine revolution signal (output)
Idling
Pulse generation
(see waveform 1)
STAR (B32-52) - E1 (B32-104)
W - BR
Starter relay drive signal
Cranking
10 to 14 V
Inspect the connector using an oscilloscope.
Waveform 1

Item
Content
Symbols (Terminal No.)
TACH (A12-15) - E1 (B32-104)
Tool Setting
5 V/DIV., 10 msec./DIV.
Condition
Engine idling
- HINT:
- As the vehicle speed increases, the wavelength shortens.
| CHECK STEERING LOCK ECU |


Disconnect the E6 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (E6-7) - Body ground
L - Body ground
+B power supply
Always
Always
IG2 (E6-6) - Body ground
B - Body ground
Ignition power supply
Ignition switch on (IG)
Always
IG2 (E6-6) - Body ground
B - Body ground
Ignition power supply
Ignition switch off
Below 1 V
GND (E6-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
SGND (E6-2) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E6 ECU connector.
Measure the voltage of the connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
SLP1 (E6-4) - GND (E6-1)
G - W-B
Steering lock actuator position signal
Steering lock locked
10 to 14 V
SLP1 (E6-4) - GND (E6-1)
G - W-B
Steering lock actuator position signal
Steering lock released
Below 1 V
- If the result is not as specified, the ECU may have a malfunction.
- If the result is not as specified, the ECU may have a malfunction.