2005-2008 RAV4 · Service Manual ENGINE

P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

Refer to DTC P2195 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2238
  1. Case 1:
Condition (a) or (b) continues for 5.0 seconds or more
(2 trip detection logic):
(a) AF+ voltage 0.5 V or less
(b) (AF+) - (AF-) = 0.1 V or less
  1. Case 2:
A/F sensor admittance: Less than 0.022 1/Ω
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater (sensor 1)
  4. Integration relay (EFI MAIN relay)
  5. A/F sensor heater and EFI MAIN relay circuits
  6. ECM
P2239
AF+ voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater (sensor 1)
  4. Integration relay (EFI MAIN relay)
  5. A/F sensor heater and EFI MAIN relay circuits
  6. ECM
P2252
AF- voltage 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater (sensor 1)
  4. Integration relay (EFI MAIN relay)
  5. A/F sensor heater and EFI MAIN relay circuits
  6. ECM
P2253
AF- voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater (sensor 1)
  4. Integration relay (EFI MAIN relay)
  5. A/F sensor heater and EFI MAIN relay circuits
  6. ECM

MONITOR DESCRIPTION

The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the A/F sensor circuit.

WIRING DIAGRAM

A127851E01

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and turn the tester ON.
  3. (c) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. (d) On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  5. (e) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (f) Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  1. The sensors react in accordance with increases and decreases in the fuel injection volume.


Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0
-12.5%
Lean
More than 3.35
O2S B1 S2
(HO2)
+25%
Rich
More than 0.5
-12.5%
Lean
Less than 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Areas
1
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
2
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost
no reaction
A103185
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
3
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
Almost
no reaction
A103185
4
Injection volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system
    (Air-fuel ratio extremely lean or rich)
Output Voltage
Almost
no reaction
A103185
Output Voltage
Almost
no reaction
A103185
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the output voltages of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Enter / View / AFS B1 S1 and O2S B1 S2.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)
A052607E27
  1. Disconnect the B7 A/F sensor connector.

  1. Measure the resistance of the A/F sensor connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    HA1A (1) - +B (2)
    1.8 Ω to 3.4 Ω at 20°C (68°F)
    HA1A (1) - A1A- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


2. INSPECT INTEGRATION RELAY (EFI MAIN RELAY)
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI MAIN fuse.

    1. A107921E13
      Remove the EFI MAIN fuse from the integration relay.

    2. Measure the EFI MAIN fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI MAIN fuse.

  1. Inspect the EFI MAIN relay.

    1. Measure the EFI MAIN relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A127715E05
  1. Disconnect the B7 A/F sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the +B terminal of the A/F sensor connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (B7-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    HA1A (B7-1) - HA1A (B32-109)
    Below 1 Ω
    A1A+ (B7-3) - A1A+ (B32-112)
    Below 1 Ω
    A1A- (B7-4) - A1A- (B32-113)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    HA1A (B7-1) or HA1A (B32-109) - Body ground
    10 kΩ or higher
    A1A+ (B7-3) or A1A+ (B32-112) - Body ground
    10 kΩ or higher
    A1A- (B7-4) or A1A- (B32-113) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.A127244E03



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE AIR FUEL RATIO SENSOR

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 5 minutes or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P2238, P2239, P2252 or P2253
    B



B
REPLACE ECM
A

END


← P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) (+ P2239, P2252, P2253) (Jan 2007 – Jul 2007)P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (Nov 2005 – Dec 2006) →