SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Nov 2005
| ENGINE CONTROL SYSTEM |


| TOYOTA D-CAT DESCRIPTION |
Diesel Clean Advanced Technology (TOYOTA D-CAT) comprehensively regulates engine control (consists of a catalytic system and a fuel injection system) that purifies both particulate matter (PM) and nitrogen oxides (NOx) discharged by diesel engines. The catalytic system purifies hydrocarbons (HC) and carbon monoxides (CO), and reduces PM and NOx with a catalytic converter with the Diesel Particulate-NOx Reduction system (DPNR). The fuel injection system adds fuel into the exhaust port using the exhaust fuel addition injector to produce a RICH state for NOx reduction and maintain a proper catalyst temperature for DPNR catalyst regeneration.


TOYOTA D-CAT components:
Component
Description
DPNR catalytic converter
Reduces HC, CO, PM, and NOx.
Exhaust fuel addition injector
Adds fuel into the exhaust port in order to produce RICH air-fuel ratio for NOx reduction. Also, raises catalyst temperature for DPNR catalyst regeneration.
Exhaust gas temperature sensor
Used for estimating DPNR catalytic converter temperature and adjusting fuel addition by ECM while DPNR catalyst regeneration is performed. Also, detects DPNR catalytic converter temperature to prevent the catalytic converter temperature from rising too high.
Differential pressure sensor
Detects the volume of PM deposits and incorrect vacuum hose arrangement on the DPNR catalytic converter.
A/F sensor
Used for controlling air-fuel ratio. By controlling the air-fuel ratio, combustion control for low temperature combustion and DPNR catalyst regeneration are properly regulated.
Diagnostic Trouble Codes (DTCs) table for TOYOTA D-CAT:
- HINT:
- This table indicates typical DTC combinations for each malfunction occurrence.
Trouble Area
Malfunction
DTC No.
DPNR catalytic converter
Deteriorated or clogged
P2002, P1601, P1386*
Exhaust fuel addition injector
Stuck open
P1386
Stuck closed
P1386, P2002*
Low fuel addition volume
P1386, P2002*
Open in exhaust fuel addition injector circuit
P1386, P2047, P2002*
Short in exhaust fuel addition injector circuit
P1386, P2047
Open or short in exhaust fuel addition injector
P1386, P2047, P2002*
Exhaust gas temperature sensor
Open in exhaust gas temperature sensor circuit
P0544, P0545, P0546, P1386, P2031, P2032, P2033
Short in exhaust gas temperature sensor circuit
P0544, P0545, P0546, P1386*, P2002*, P2031, P2032, P2033
Exhaust gas temperature sensor
P0544, P0545, P0546, P1386*, P2031, P2032, P2033
Differential pressure sensor
Open in differential pressure sensor circuit
P1425, P1427, P2002*
Short in differential pressure sensor circuit
P1425, P1427, P2002*
Differential pressure sensor
P1425, P1427, P2002*
Differential pressure sensor clogged
P1426, P2002*
Incorrect vacuum hose arrangement of the differential pressure sensor
P1426, P2002*
A/F sensor
Open or short in A/F sensor or heater circuit
P0031, P0032, P1386*, P2238, P2239, P2252, P2253
A/F sensor
P0031, P0032, P1386*, P2238, P2239, P2252, P2253
Exhaust gas leaks
Exhaust gas leaks
P1386*, P2002*
Fuel leaks
Fuel leaks in fuel addition injector
P1386*
Supply pump
Correct fuel pressure cannot be fed to the exhaust fuel addition injector
P1386*
- HINT:
- *: There may be no DTC output depending on the condition of the malfunction.
Diagnostic trouble code description for TOYOTA D-CAT:
DTC No.
Description
P0031
Open or short in A/F sensor heater control circuit (low output)
P0032
Open or short in A/F sensor or heater circuit (high output)
P0544
Open or short in exhaust gas temperature sensor circuit (upstream)
P0545
Open or short in exhaust gas temperature sensor circuit (upstream) (low output)
P1386
Open or short in exhaust gas temperature sensor circuit (upstream) (high output)
P1425
TOYOTA D-CAT fuel addition system malfunction
P1426
Differential pressure sensor is clogged or has incorrect vacuum hose arrangement
P1427
Open or short in differential pressure sensor circuit (low output)
P1428
Open or short in differential pressure sensor circuit (high output)
P2002
DPNR catalytic converter malfunction
P2031
Open or short in exhaust gas temperature sensor circuit (downstream)
P2032
Open or short in exhaust gas temperature sensor circuit (downstream) (low output)
P2033
Open or short in exhaust gas temperature sensor circuit (downstream) (high output)
P2047
Open in exhaust fuel addition injector circuit
P2238
Open or short in A/F sensor or heater circuit (low output)
P2239
Open or short in A/F sensor or heater circuit (high output)
P2252
Open or short in A/F sensor or heater circuit (low output)
P2253
Open or short in A/F sensor or heater circuit (high output)
| COMMON RAIL SYSTEM DESCRIPTION |
Common rail system:
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power, while suppressing engine vibration and noise.
This system stores fuel in the common rail, which has been pressurized and supplied by the supply pump. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM, using the EDU, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the supply pump to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a piezo actuator inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
The common rail system allows a two stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.

Common rail system components:
Component
Description
Common rail
Stores high-pressure fuel produced by supply pump
Supply pump
Operated by crankshaft
Supplies high-pressure fuel to common rail
Injector
Injects fuel to combustion chamber based on signals from ECM
Fuel pressure sensor
Monitors internal fuel pressure of common rail and sends signals to ECM
Pressure Discharge Valve
Based on signals from the ECM, opens valve when sudden deceleration has occurred, or when the ignition switch is off to prevent the fuel pressure from becoming too high.
Suction control valve
Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure
Check valve
Keeps pressure that discharges from injector
Diagnostic trouble codes (DTCs) table for the common rail system
- HINT:
- This table indicates typical DTC combinations for each malfunction occurrence.
Trouble Area
Malfunction
DTC No.
Injector
Open or short in injector circuit
P0200, P1238, P0093*
Stuck open
P0093, P1238
Stuck closed
P1238
Fuel pressure sensor
Open or short in fuel pressure sensor circuit or pressure sensor output fixed
P0087, P0190, P0191, P0192, P0193
Pressure discharge valve
Open or short in pressure discharge valve circuit
P1271, P1272, P0088*, P0093*, P1229*
Stuck open
P0093
Stuck closed
P1272, P0088*
Suction control valve
Open or short in suction control valve circuit
P0627, P1229, P0088*
Stuck open
P1229, P0088*
EDU
Faulty EDU
P0093*, P0200*, P1238*, P1271*, P1272*
Common rail system (fuel system)
Fuel leaks in high-pressure area
P0093
- HINT:
- *: There may be no DTC output depending on the condition of the malfunction.
Diagnostic trouble code description for the common rail system:
DTC No.
Description
P0087
Fuel pressure sensor output does not change
P0088
Internal fuel pressure too high (200 MPa [2,039 kgf/cm2, 29,007 psi] or more)
P0093
Fuel leaks in high-pressure areas
P0190
Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
P0192
Open or short in fuel pressure sensor circuit (output voltage is too low)
P0193
Open or short in fuel pressure sensor circuit (output voltage is too high)
P0200
Open or short in EDU or injector circuit
P0627
Open or short in suction control valve circuit
P1229
Fuel over-feed
| INJECTION CONTROL SYSTEM DESCRIPTION |
The ECM determines the injection volume and injection timing based on signals from the acceleration position sensor, crank position sensor, and camshaft position sensor. Based on the signals from the ECM, the EDU controls the injectors. The EDU also controls the suction control valve installed on the supply pump to help regulate fuel pressure.
The piezo type injector used in the 2AD-FHV engine makes noise when the engine is idling because this injector operates at high speed. Therefore, the EDU controls the injector to operate at low speed when the engine is idling based on signals from the ECM to achieve noise reduction.
The feed pump is used to pump fuel from the fuel tank to the supply pump.


| SUPPLY PUMP OPERATION SYSTEM DESCRIPTION |


| SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION |
- HINT:
- The ECM controls the suction control valve operation to regulate the fuel volume that is produced by the supply pump for the common rail. This control is performed to regulate the internal fuel pressure of the common rail to the targeted injection pressure.
Small opening of the suction control valve:
(1) When the opening of the suction control valve is small, the volume of supplied fuel is small.
(2) The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.
(3) Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).

Large opening of the suction control valve:
(1) When the opening of the suction control valve is large, the volume of supplied fuel is increased.
(2) If the plunger stroke is full, the suction volume becomes large because of the wide path.
(3) Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).
