2005-2008 RAV4 · Service Manual ENGINE

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Nov 2005


ENGINE CONTROL SYSTEM
A135530E01

COMMON RAIL SYSTEM DESCRIPTION

  1. Common rail system:
    The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power, while suppressing engine vibration and noise.
    This system stores fuel in the common rail, which has been pressurized and supplied by the supply pump. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
    The ECM, using the EDU, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the supply pump to supply the fuel necessary to obtain the target fuel pressure.
    In addition, this system uses the 2-Way Valve (TWV) inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
    The common rail system allows a two stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine" vibration and noise.
    A134313E01

  2. Common rail system components:

    Component
    Description
    Common rail
    Stores high-pressure fuel produced by supply pump
    Supply pump
    Operated by crankshaft
    Supplies high-pressure fuel to common rail
    Injector
    Injects fuel to combustion chamber based on signals from ECM
    Fuel pressure sensor
    Monitors internal fuel pressure of common rail and sends signals to ECM
    Pressure limiter
    Opens pressure limiter valve to reduce internal pressure in common rail when common rail pressure exceeds specified level
    Suction control valve
    Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure

  3. Diagnostic trouble codes (DTCs) table for the common rail system

    HINT:
    This table indicates typical DTC combinations for each malfunction occurrence.

    Trouble Area
    Malfunction
    DTC No.
    Injector
    Open or short in injector circuit
    P0200/97, P0088/78*
    Injector
    Stuck open
    P0088/78
    Fuel pressure sensor
    Open or short in fuel pressure sensor circuit or pressure sensor output fixed
    P0087/49, P0190/49, P0192/49, P0193/49
    Pressure limiter
    Stuck open
    P0093/78
    Pressure limiter
    Stuck closed
    P0088/78*
    Suction control valve
    Open or short in suction control valve circuit
    P0627/78, P1229/78, P0088/78*
    Suction control valve
    Stuck open
    P1229/78, P0088/78*
    EDU
    Faulty EDU
    P0093/78*, P0200/97*
    Common rail system (Fuel system)
    Fuel leaks in high-pressure areas
    P0093/78

    HINT:
    *: There may be no DTC output depending on the condition of the malfunction.


INJECTION CONTROL SYSTEM DESCRIPTION
The ECM controls the fuel injection system by using the injectors and supply pump. The ECM regulates the fuel injection volume and fuel injection timing by controlling both the duration and timing of energization to the solenoid valve in the injector. The ECM regulates injection pressure by controlling the suction control valve located in the supply pump.
The feed pump is used to pump fuel from the fuel tank to the supply pump.
A081479E04

SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
The rotation of the eccentric cam in the supply pump causes the ring cam to push plunger A upward as illustrated below. The spring force pulls plunger B (located opposite to plunger A) upward. As a result, plunger B draws the fuel in, and plunger A pumps fuel out at the same time.
A130185E02

SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION

HINT:
The ECM controls the suction control valve operation to regulate the fuel volume that is produced by the supply pump for the common rail. This control is performed to regulate the internal fuel pressure of the common rail to the targeted injection pressure.

  1. Small opening of the suction control valve:
    (1) When the opening of the suction control valve is small, the volume of supplied fuel is small.
    (2) The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.
    A130184E01
    (3) Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).

  2. Large opening of the suction control valve:
    (1) When the opening of the suction control valve is large, the volume of supplied fuel is increased.
    (2) If the plunger stroke is full, the suction volume becomes large because of the wide path.
    (3) Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).
    A130181E01

← SYSTEM DIAGRAM (from Nov 2005)HOW TO PROCEED WITH TROUBLESHOOTING (Nov 2005 – Dec 2006) →