Engine does not Start
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
| ENGINE START SYSTEM OPERATION |
When the engine switch is pressed with the clutch pedal (M/T) or brake pedal (A/T) with shift lever in P or N depressed, the main body ECU determines that it is an engine start request.
The certification ECU and other ECUs perform key verification via the LIN communication line.
The main body ECU activates the ACC relay.
The main body ECU activates the IG1 and IG2 relays. The engine switch indicator light illuminates in green.
The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the main body ECU.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC cut request signal to the main body ECU.
The ECM and main body ECU activate the ST cut relay.
The main body ECU deactivates the ACC relay until the ECU detects an engine start.
The ECU reactivates the ACC relay and turns off the engine switch indicator light.
Symbols of main body ECU
Signals
SSW1/SSW2
Ignition switch on (ACC, IG) signal
ACCD
ACC relay operation signal
IG2D
IG2 relay operation signal
STR2
ST cut relay operation signal
STR
Clutch start switch (M/T) or park / neutral position switch (A/T) signal
STP
Stop light switch (A/T) signal
TACH
Engine start detection signal
STSW
Starter activation request signal
ACCR
ACC cut request signal


WIRING DIAGRAM
See CRANKING HOLDING FUNCTION CIRCUIT (Click here).INSPECTION PROCEDURE
| 1. CHECK WHETHER ENGINE STARTS AFTER STEERING LOCK INITIALIZATION |
Open and close the driver door when the ignition switch is off.
Check that the engine starts.
- OK:
- Engine starts.
- HINT:
- After the battery runs out, the engine may not start if the steering lock ECU has not been initialized (lock / unlock may not be recorded) through the procedure described above.
|
|
||||
| NG | |
| 2. CHECK WHETHER DTC OUTPUT RECURS |
Clear the DTCs.
- HINT:
- After all DTCs are cleared, check if the trouble occurs again 5 seconds after the ignition switch is turned on (IG).
Check for DTCs again.
- OK:
- No DTC is output.
|
|
||||
| OK | |
| 3. CHECK SWITCH CONDITION |
Ensure the electrical key is inside the cabin.
Check that the power source mode changes as shown below each time the ignition switch is pushed.
- OK:
- off → on (ACC) → on (IG) → off
|
|
||||
| OK | |
| 4. CHECK BASIC FUNCTION |
Ensure there is fuel in the fuel tank and the key is inside the cabin.
Depress the clutch pedal (M/T) or brake pedal (A/T) with the shift lever in P or N, and keep depressing the pedal.
Check that the engine cranks when the engine switch is pressed.
- OK:
- Engine cranks.
|
|
||||
| NG | |
| 5. READ VALUE USING INTELLIGENT TESTER (N SW / C SW) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Body / Main Body ECU / Data List / N SW / C SW.
Read the displays on the tester.
- Main body ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
N SW / C SW
Clutch start switch (M/T) or park / neutral position switch (A/T) / ON or OFF
ON: Clutch pedal is depressed (M/T), shift lever in P or N (A/T)
OFF: Clutch pedal is released (M/T), shift lever in R or D (A/T)
-
- OK:
- When the clutch pedal is depressed, ON is displayed on the tester.
When the shift lever is in P or N, ON is displayed on the tester.
|
|
||||
| OK | |
| 6. CHECK STEERING LOCK SYSTEM |
When the ignition switch is on (ACC), check that the steering lock can be released.
- OK:
- Steering lock can be released.
|
|
||||
| OK | |
| 7. INSPECT MAIN BODY ECU |
Disconnect the E20 main body ECU connector.

Depress the clutch pedal (M/T) or brake pedal (A/T) with the shift lever in P or N, and keep depressing the pedal.
Measure the voltage of the wire harness side connector when the engine cranks by pressing the engine switch.
- Standard voltage:
Tester Connection
Specified Condition
E20-4 (STSW) - Body ground
10 to 14 V
|
|
||||
| OK | ||
| ||
| 8. READ VALUE USING INTELLIGENT TESTER (L CODE CHECK) |
Place the electrical key inside the vehicle.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / L Code Chk.
Read the display on the tester.
- Certification ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
L Code Chk
L Code Check / NG or OK
NG: L code certification result is abnormal
OK: L code certification result is normal
-
- OK:
- L code check result is OK.
|
|
||||
| OK | |
| 9. READ VALUE USING INTELLIGENT TESTER (S CODE CHECK) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / S Code Chk.
Read the display on the tester.
- Certification ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
S Code Chk
S Code Check / NG or OK
NG: S code certification result is abnormal
OK: S code certification result is normal
-
- OK:
- S code check result is OK.
|
|
||||
| OK | |
| 10. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) (do not start the engine) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / Start Req Sig.
Read the displays on the tester.
- Certification ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
Start Rqst
Starter request signal / Yes or No
YES: ID code box receives immobiliser unset signal
NO: ID code box does not receive immobiliser unset signal
-
- OK:
- When ID code box receives immobiliser unset signal, YES is displayed on tester.
|
|
||||
| YES | ||
| ||
