2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007


1. INSTALL FUEL TANK ASSEMBLY

A127921E01
  1. Set the fuel tank on a mission jack.

  1. Lift up the mission jack.

  1. Fold back the 2 cushion rubbers.

  1. Connect the sender gauge connector to the fuel tank.

    NOTICE:
    Be careful not to cut the wirings.

  1. Attach the wire harness to the 2 clamps.

  1. A124665
    Install the 3 fuel tank bands with the 6 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


2. INSTALL FUEL TANK FILLER PIPE
  1. Install the filler pipe with the 2 bolts.

    Torque:
    23.5 N*m{ 240 kgf*cm , 17 ft.*lbf }

  1. Install the filler pipe protector with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


3. CONNECT FUEL TANK TO FILLER PIPE HOSE

A124662
  1. Connect the filler pipe hose to the fuel tank.


4. CONNECT FUEL TANK BREATHER HOSE

  1. A131628
    Connect the fuel tank breather hose to the fuel tank.

    NOTICE:
    1. Before installing the pipe, make sure that it is not damaged. Make sure that there are no dirt present on the connecting surfaces.
    1. After connecting, check if the pipe and the connector are securely connected by pulling on them.


5. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

NOTICE:
Before installing the tube connectors to the pipes, check the connectors for damage and foreign matter.

  1. A130274E01
    Connect the main tube connector to the pipe. Push the 2 parts together firmly until a "click" sound is heard.

    NOTICE:
    Check that the connectors and pipes are securely connected by trying to pull them apart.

  1. Connect the fuel tank return tube.


6. INSTALL NO. 1 FUEL TANK PROTECTOR
  1. Install the fuel tank protector with the 3 clips and 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


7. INSTALL NO. 1 FLOOR UNDER COVER

  1. A124659
    Install the floor under cover with the clip and 2 nuts.


8. INSTALL FRONT FLOOR COVER

  1. A130273
    Install the floor cover with the 3 clips, bolt and nut.


9. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

  1. A124660
    Connect the parking brake cable with the 2 bolts.


10. INSTALL FUEL TANK CAP

11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

12. BLEED AIR FROM FUEL SYSTEM

  1. A130544
    Using the hand pump, bleed air from the fuel system until pumping becomes difficult.


13. CHECK FOR FUEL LEAKS
  1. PERFORM ACTIVE TEST

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine.

    3. Turn the intelligent tester ON.

    4. Enter the following menus: Powertrain / Engine / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizing common rail internal fuel pressure, and checking for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when start is selected
      2. Above conditions to be maintained while test is started

← INSTALLATION (Nov 2005 – Dec 2006)PRECAUTION (from Nov 2005) →