2005-2008 RAV4 · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2007


1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C099458
    Remove the nut, washer and control shaft lever.

  1. C161138
    Using a screwdriver, pry off the lock plate.

  1. G025453
    Remove the nut and lock plate.

  1. C099454
    Remove the 2 bolts and pull out the switch.


2. REMOVE BREATHER PLUG HOSE
  1. Remove the breather plug hose from the transaxle case.


3. REMOVE OIL COOLER OUTLET TUBE ELBOW

  1. C136351E01
    Remove the elbow.

  1. Remove the O-ring from the elbow.


4. REMOVE OIL COOLER INLET TUBE ELBOW

  1. C136352E01
    Remove the elbow.

  1. Remove the O-ring from the elbow.


5. REMOVE SPEED SENSOR

  1. D030672E06
    Remove the 2 bolts and the 2 speed sensors from the transaxle.


6. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C136368
    Remove the 4 No. 1 transaxle case plugs from the transaxle case.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.


7. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and speedometer driven hole cover sub-assembly.

  1. Remove the O-ring from the speedometer driven hole cover sub-assembly.


8. SECURE AUTOMATIC TRANSAXLE ASSEMBLY

  1. D009176E01
    Secure the transaxle.


9. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. C091925E01
    Remove the 18 bolts, oil pan and gasket.

  1. C086316E02
    Remove the 2 magnets from the oil pan.


10. INSPECT TRANSMISSION OIL CLEANER MAGNET

  1. AT00103E01
    Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.

    Result:
    Steel (magnetic):
    Bearing, gear and plate wear
    Brass (non-magnetic):
    Bushing wear


11. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. C091931E02
    Remove the 3 bolts and oil strainer.

  1. C091932E02
    Remove the O-ring from the oil strainer.


12. REMOVE TRANSMISSION WIRE

  1. C134996E01
    Remove the 7 connectors from the shift solenoid valves.

  1. Remove the bolt, lock plate and temperature sensor.

  1. D003547E07
    Remove the bolt and transmission wire from the transaxle case.


13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. C091933E07
    Support the valve body and remove the 17 bolts and valve body assembly.


14. REMOVE NO. 1 GOVERNOR APPLY GASKET

  1. C083127E01
    Remove the No. 1 governor apply gasket from the transaxle case.


15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

  1. C083128E01
    Remove the transaxle case 2nd brake gasket from the transaxle case.


16. REMOVE BRAKE DRUM GASKET

  1. C083129E01
    Remove the brake drum gasket from the transaxle case.


17. REMOVE CHECK BALL BODY

  1. D003554E01
    Remove the check ball body and spring from the transaxle case.


18. REMOVE C-3 ACCUMULATOR PISTON

  1. D003555E01
    Remove the spring from the C-3 accumulator piston.

  1. D003556E01
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying compressed air.

  1. D003902E02
    Remove the O-ring from the C-3 accumulator piston.


19. REMOVE REVERSE CLUTCH ACCUMULATOR PISTON

  1. D026401E01
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the reverse clutch accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying compressed air.

  1. D026402E09
    Remove the 2 O-rings from the reverse clutch accumulator piston.


20. REMOVE B-3 ACCUMULATOR PISTON

  1. D003558E01
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying compressed air.

  1. D003904E05
    Remove the O-ring from the B-3 accumulator piston.


21. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING

  1. D003559E01
    Using needle-nose pliers, remove the manual valve lever shaft retainer spring.


22. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

  1. D003560E03
    Remove the 2 bolts, manual detent spring sub-assembly and cover.


23. REMOVE PARKING LOCK PAWL BRACKET

  1. C056727E01
    Remove the 2 bolts and parking lock pawl bracket.


24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

  1. D003563E01
    Using a chisel and hammer, cut off and remove the spacer.

  1. D003564E01
    Using a pin punch (φ3.5 mm) and hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it does not fall into the transaxle case.

  1. D003565E02
    Remove the manual valve lever shaft and manual valve lever.


25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. D026382E02
    Remove the parking lock rod from the manual valve lever.


26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. D003566E02
    Using a screwdriver, pry out the manual valve lever shaft oil seal from the transaxle case.

    NOTICE:
    Do not apply excessive force when removing the manual valve lever shaft oil seal.


27. SECURE AUTOMATIC TRANSAXLE ASSEMBLY
  1. Secure the transaxle case in place with the oil pump side facing up.


28. INSPECT INPUT SHAFT END PLAY

  1. D008091E02
    Using a dial indicator, measure the input shaft end play.

    Standard end play:
    0.262 to 1.244 mm (0.01 to 0.049 in.)

    If the result is not as specified, replace the input shaft or thrust needle roller bearing.


29. REMOVE TRANSAXLE HOUSING

  1. D003568E03
    Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic-faced hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed while removing the transaxle housing.


30. REMOVE OIL PUMP ASSEMBLY

  1. D003569E03
    Remove the 7 bolts and oil pump from the transaxle case.


31. REMOVE THRUST NEEDLE ROLLER BEARING

  1. D025505E03
    Remove the thrust needle roller bearing from the underdrive planetary gear assembly.


32. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE

  1. D025506E04
    Remove the thrust bearing underdrive race from the underdrive planetary gear assembly.


33. REMOVE DIFFERENTIAL GEAR ASSEMBLY

  1. D026450E09
    Remove the differential gear assembly from the transaxle case.


34. REMOVE OVERDRIVE BRAKE GASKET

  1. D003573E01
    Remove the 2 overdrive brake gaskets from the transaxle case.


35. REMOVE FORWARD CLUTCH ASSEMBLY

  1. D003574E03
    Remove the forward clutch assembly from the transaxle case.

  1. D003906E02
    Remove the thrust needle roller bearing from the forward clutch.


36. REMOVE MULTIPLE DISC CLUTCH HUB

  1. D026787E10
    Remove the thrust needle roller bearing, multiple disc clutch hub, thrust needle roller bearing and No. 1 thrust bearing race from the transaxle case.


37. INSPECT MULTIPLE DISC CLUTCH HUB

  1. D003829E03
    Using a caliper gauge, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.03 to 23.05 mm (0.9067 to 0.9075 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. Check the contact surface of the bushing in the direct clutch shaft. If any scratches or discoloration is found, replace the direct clutch assembly with a new one.

    If the inside diameter is greater than the maximum, replace the forward clutch hub with a new one.


38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. D003576E03
    Remove the bolt and pawl shaft clamp.

  1. D009652E01
    Remove the parking lock pawl shaft.

  1. D009689E01
    Push the parking lock pawl.

    HINT:
    Failure to do so will cause interference when the underdrive planetary gear is removed.

  1. D003579E04
    Remove the underdrive planetary gear from the transaxle case.

    NOTICE:
    Make sure that the underdrive planetary gear assembly will not fall off.


39. REMOVE PARKING LOCK PAWL

  1. D026386E01
    Remove the spring, pawl pin and parking lock pawl.


40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY

  1. D003580E04
    Remove the underdrive clutch assembly, thrust bearing and bearing race from the transaxle case.


41. REMOVE UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003581E02
    Using a screwdriver, remove the snap ring from the transaxle case.

    NOTICE:
    Do not apply excessive force when removing the snap ring.

  1. D003627E03
    Remove the underdrive one-way clutch from the transaxle case.

  1. D003907E02
    Remove the outer race retainer from the one-way clutch.


42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC

  1. D026466E02
    Using a screwdriver, remove the snap ring.

    NOTICE:
    Do not apply excessive force when removing the snap ring.

  1. D026385E02
    Remove the flange, 4 discs and 4 plates from the transaxle case.


43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC

  1. D009196E01
    Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or is discolored, or if a part of the groove is worn, replace all the discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.


44. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

  1. C136369
    Remove the 11 bolts.

  1. Tap on the circumference of the rear cover with a plastic hammer to remove the rear transaxle cover from the transaxle case.


45. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C138647
    Remove the 4 No. 1 transaxle case plugs from the rear transaxle cover.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.


46. REMOVE REAR CLUTCH OIL SEAL RING OUTER

  1. D026389E03
    Remove the 3 rear clutch oil seal rings from the transaxle rear cover.


47. REMOVE NEEDLE ROLLER BEARING

  1. D026472E01
    Using SST, remove the needle roller bearing from the rear transaxle cover.
    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)


48. REMOVE NO. 1 GOVERNOR APPLY GASKET

  1. D026390E01
    Using a screwdriver, remove the 3 No. 1 governor apply gaskets.


49. REMOVE BRAKE APPLY TUBE

  1. D026391E05
    Remove the bolt, clamp and brake apply tube.

  1. Remove the clutch apply tube.

  1. Remove the brake apply tube from the clamp.

    NOTICE:
    Do not bend the tubes.


50. REMOVE DIRECT CLUTCH ASSEMBLY

  1. D026403E06
    Remove the thrust bearing and the direct clutch assembly from the transaxle case.


51. REMOVE OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY

  1. D026392E09
    Remove the thrust bearing race, thrust bearing and overdrive direct clutch hub from the planetary gear.


52. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. D003829E03
    Using a caliper gauge, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. Check the contact surface of the bushing in the direct clutch shaft. If any scratches or discoloration is found, replace the direct clutch assembly with a new one.

    If the inside diameter is greater than the maximum, replace the forward clutch hub with a new one.


53. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

  1. D026714E05
    Remove the rear planetary sun gear assembly from the transaxle case.

  1. D026404E07
    Remove the thrust needle roller bearing and thrust bearing race from the rear planetary sun gear assembly.

  1. D026393E05
    Remove the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.


54. REMOVE ONE-WAY CLUTCH ASSEMBLY

  1. D026598E06
    Remove the one-way clutch assembly and thrust needle roller bearing from the transaxle case.

  1. D003909E02
    Remove the one-way clutch inner race from the one-way clutch assembly.


55. REMOVE ONE-WAY CLUTCH SLEEVE OUTER

  1. D003589E03
    Remove the one-way clutch sleeve outer from the transaxle case.


56. REMOVE NO. 1 PLANETARY CARRIER THRUST WASHER

  1. D026394E07
    Remove the No. 1 planetary carrier thrust washer from the planetary gear assembly.


57. REMOVE 2ND BRAKE CLUTCH DISC

  1. D026395E03
    Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs and 4 plates from the transaxle case.


58. INSPECT 2ND BRAKE CLUTCH DISC

  1. D026717E01
    Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or is discolored, or if a part of the groove is worn, replace all the discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.


59. REMOVE 2ND BRAKE PISTON ASSEMBLY

  1. D008058E03
    Using a screwdriver, remove the snap ring.

  1. D026396E06
    Remove the 2nd brake piston assembly from the transaxle case.


60. REMOVE REAR PLANETARY GEAR ASSEMBLY

  1. D003616E02
    Using a screwdriver, remove the snap ring.

  1. D026591E04
    Remove the rear planetary gear assembly from the transaxle case.


61. REMOVE INPUT SUN GEAR

  1. D003873E03
    Remove the 2 thrust needle roller bearings, No. 2 thrust bearing race and the input sun gear from the transaxle case.


62. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC

  1. D026397E01
    Remove the flange, 6 discs and 6 plates from the transaxle case.


63. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

  1. D009189E01
    Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or is discolored, or if a part of the groove is worn, replace all the discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.


64. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. D003595E02
    Using a chisel and hammer, release the lock washer.

    NOTICE:
    Push down all the claws of the washer. Otherwise SST cannot be fully pressed against the nut, and cannot loosen the nut.

  1. D003596E01
    Using SST, remove the nut.
    SST
    09387-00030  
    09387-00080  

  1. D026398E01
    Using SST and a press, remove the front planetary gear assembly from the counter drive gear.
    SST
    09950-60010   (09951-00450)
    09950-70010   (09951-07100)

  1. D026763E03
    Remove the front planetary gear assembly from the brake hub.


65. REMOVE FRONT PLANETARY RING GEAR

  1. D003615E05
    Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.


66. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D003600E01
    Place SST on the return spring, and compress the return spring with a press.

    NOTICE:
    Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, to prevent the spring seat from being deformed.

    SST
    09387-00070  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    Do not expand the snap ring excessively.


67. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D030852E09
    Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.61 mm (0.6933 in.)

    If the result is not as specified, replace the spring.


68. REMOVE 1ST AND REVERSE BRAKE PISTON

  1. D026405E04
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying compressed air.

  1. D026713E04
    Remove the 2 O-rings from the 1st and reverse brake piston.


69. REMOVE COUNTER DRIVE GEAR

  1. C089120E01
    Using SST and a press, remove the counter drive gear from the transaxle case.
    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)

  1. D003602E01
    As shown in the illustration, tighten the 2 bolts evenly and make a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and the inner race.

  1. D003603E01
    Using SST, remove the tapered roller bearing.
    SST
    09950-60010   (09951-00590)
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)


70. REMOVE TRANSFER DRIVEN PINION FRONT BEARING

  1. D026467E02
    Using a snap ring expander, remove the snap ring.

  1. C089121E01
    Using SST and a press, remove the bearing outer race.
    SST
    09950-60020   (09951-00910)


71. REMOVE NO. 2 BREATHER PLUG

72. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D026407E02
    Place SST on the return spring, and compress the return spring with a press.

    NOTICE:
    Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.

    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    Do not expand the snap ring excessively.


73. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D030852E09
    Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    13.24 mm (0.5213 in.)

    If the result is not as specified, replace the spring.


74. REMOVE UNDERDRIVE BRAKE PISTON

  1. D026406E03
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.

  1. D003794E02
    Remove the 2 O-rings from the underdrive brake piston.


75. REMOVE NEEDLE ROLLER BEARING

  1. D003605E04
    Using SST, remove the needle roller bearing from the transaxle case.
    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)


76. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING

  1. D003914E04
    Remove the 2 underdrive clutch drum oil seal rings from the transaxle case.


77. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. D026383E01
    Remove the 2 No. 1 transaxle case plugs.

  1. Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.


78. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING

  1. D003606E03
    Using SST, remove the underdrive cylindrical roller bearing from the transaxle case.
    SST
    09514-35011  


79. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING

  1. D003915E09
    Remove the oil seal ring from the transaxle housing.


80. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. D026400E06
    Remove the bolt, transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.

    NOTICE:
    Do not bend the tubes.

← COMPONENTS (from Aug 2007)INSPECTION (from Aug 2007) →