2005-2008 RAV4 · Service Manual ENGINE

P1550 Battery Current Sensor Circuit

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The battery current sensor installed on the positive battery terminal detects the amount of current supplied from the alternator.
A110645E01
The battery current sensor changes current to voltage and outputs that voltage. The battery current sensor changes current at the positive battery terminal to voltage and sends it to the ECM. The ECM controls the voltage of the alternator based on the signals from the battery current sensor.
DTC No.
DTC Detection Condition
Trouble Area
P1550
The following condition continues for 10 seconds or more with the ignition switch on (IG)
(1 trip detection logic):
  1. Difference between the maximum and minimum current values of the battery current sensor is 1 A or less
  1. Battery current sensor
  2. Wire harness or connector
  3. ECM
P1551
Battery current sensor output value is 0.2 V or less for 0.55 seconds or more with the ignition switch on (IG)
(1 trip detection logic)
  1. Battery current sensor
  2. Wire harness or connector
  3. ECM
P1552
Battery current sensor output value is 4.8 V or more for 0.55 seconds or more with the ignition switch on (IG)
(1 trip detection logic)
  1. Battery current sensor
  2. Wire harness or connector
  3. ECM

WIRING DIAGRAM

Refer to DTC P0516 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.


1. INSPECT BATTERY CURRENT SENSOR ASSEMBLY

  1. C129062E02
    Disconnect the B31 battery current sensor connector.

  1. Measure the resistance of the battery current sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    B31-2 (VC5) - B31-4 (E2)
    3 to 10 kΩ
    B31-3 (IB)- B31-4 (E2)
    3 to 10 kΩ
    B31-2 (VC5) - B31-3 (IB)
    Below 0.5 kΩ

    HINT:
    The resistance differs according to the tester type.

  1. Reconnect the battery current sensor connector.



NG
REPLACE BATTERY CURRENT SENSOR ASSEMBLY
OK


2. CHECK WIRE HARNESS (BATTERY CURRENT SENSOR - ECM)
A131549E02
  1. Disconnect the B31 battery current sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B31-2 (VC5) - B32-70 (VCIB)
    Below 1 Ω
    B31-3 (IB)- B32-116 (IB)
    Below 1 Ω
    B31-4 (E2) - E1 (B32-109)
    Below 1 Ω
    B31-2 (VC5) or B32-70 (VCIB) - Body ground
    10 kΩ or higher
    B31-3 (IB)or B32-116 (IB) - Body ground
    10 kΩ or higher

  1. Reconnect the battery current sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← P1426 Differential Pressure Sensor Installation Error (from Nov 2005)P1550 Battery Current Sensor Circuit (+ P1551, P1552) (from Jan 2007) →