TERMINALS OF ECU
System information · Vehicles built from Nov 2005
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (ON DRIVER DOOR) (POWER WINDOW ECU) |


Disconnect the H4*1 or G9*2 motor connector (on the driver side).
Measure the resistance and voltage of the wire harness side connector.
for LHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (H4-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (H4-2) - GND (H4-1)
GR - W-B
Battery power supply
Always
9 to 14 V
UP (H4-10) - DOWN (H4-7)
P - W
Driver side door power window regulator motor UP DOWN
Always
Below 1 Ω
If the result is not as specified, there may be a malfunction on the wire harness side.for RHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (G9-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (G9-2) - GND (G9-1)
GR - W-B
Battery power supply
Always
9 to 14 V
UP (G9-10) - DOWN (G9-7)
W - B
Driver side door power window regulator motor UP DOWN
Always
Below 1 Ω
Reconnect the H4*1 or G9*2 motor connector (on the driver side).
Measure the voltage of the connector.
for LHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
LED (H4-5) - GND (H4-1)
SB - W-B
Ignition power supply
Ignition switch on (IG)
9 to 14 V
If the result is not as specified, the motor may have a malfunction.for RHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
LED (G9-5) - GND (G9-1)
LG - W-B
Ignition power supply
Ignition switch on (IG)
9 to 14 V
| CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |


Disconnect the H2*1 or G8*2 switch connector.
Measure the resistance and voltage of the wire harness side connector.
for LHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E (H2-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (H2-6) - Body ground
L - Body ground
Ignition power supply
Ignition switch on (IG)
9 to 14 V
B (H2-6) - Body ground
L - Body ground
Ignition power supply
Ignition switch off
Below 1 V
If the result is not as specified, there may be a malfunction on the wire harness side.for RHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
E (G8-9) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (G8-6) - Body ground
L - Body ground
Ignition power supply
Ignition switch on (IG)
9 to 14 V
B (G8-6) - Body ground
L - Body ground
Ignition power supply
Ignition switch off
Below 1 V
Reconnect the H2*1 or G8*2 switch connector.
Reset the power window regulator motor.
Measure the voltage of the connector.
for LHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
U (H2-8) - E (H2-1)
P - W-B
Driver side door power window regulator motor UP output
Ignition switch on (IG), driver power window regulator switch off
9 to 14 V
U (H2-8) - E (H2-1)
P - W-B
Driver side door power window regulator motor UP output
Ignition switch on (IG), driver side power window regulator switch UP (manual operation)
9 to 14 V → Below 1 V
U (H2-8) - E (H2-1)
P - W-B
Driver side door power window regulator motor UP output
Ignition switch on (IG), driver side power window fully open → driver side power window regulator switch UP (AUTO operation) → driver side power window fully closed
Below 1 V → 9 to 14 V → Below 1 V
D (H2-5) - E (H2-1)
W - W-B
Driver side door power window regulator motor DOWN output
Ignition switch on (IG), driver side power window regulator switch DOWN (manual operation)
Below 1 V → 9 to 14 V
D (H2-5) - E (H2-1)
W - W-B
Driver side door power window regulator motor DOWN output
Ignition switch on (IG), driver side power window fully closed → driver side power window regulator switch DOWN (AUTO operation) → driver side power window fully open
Below 1 V → 9 to 14 V → Below 1 V
for RHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
U (G8-1) - E (G8-9)
W - W-B
Driver side door power window regulator motor UP output
Ignition switch on (IG), driver power window regulator switch off
9 to 14 V
U (G8-1) - E (G8-9)
W - W-B
Driver side door power window regulator motor UP output
Ignition switch on (IG), driver side power window regulator switch UP (manual operation)
9 to 14 V → Below 1 V
U (G8-1) - E (G8-9)
W - W-B
Driver side door power window regulator motor UP output
Ignition switch on (IG), driver side power window fully open → driver side power window regulator switch UP (AUTO operation) → driver side power window fully closed
Below 1 V → 9 to 14 V → Below 1 V
D (G8-5) - E (G8-9)
B - W-B
Driver side door power window regulator motor DOWN output
Ignition switch on (IG), driver side power window regulator switch off → DOWN (manual operation)
Below 1 V → 9 to 14 V
D (G8-5) - E (G8-9)
B - W-B
Driver side door power window regulator motor DOWN output
Ignition switch on (IG), driver side power window fully closed → driver side power window regulator switch DOWN (AUTO operation) → driver side power window fully open
Below 1 V → 9 to 14 V → Below 1 V
| CHECK POWER WINDOW REGULATOR SWITCH (for Passenger Side) |


Disconnect the G3*1 or H8*2 switch connector.
Measure the voltage of the wire harness side connector.
for LHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (G3-3) - Body ground
L - Body ground
Ignition power supply
Ignition switch on (IG)
9 to 14 V
If the result is not as specified, there may be a malfunction on the wire harness side.for RHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (H8-3) - Body ground
L - Body ground
Ignition power supply
Ignition switch on (IG)
9 to 14 V
Reconnect the G3*1 or H8*2 switch connector.
Measure the voltage of the wire harness side connector.
for LHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (G3-3) - D (G3-1)
L - B
Passenger side door power window regulator motor UP output
Ignition switch on (IG), front passenger window regulator switch off
Below 1 V
B (G3-3) - D (G3-1)
L - B
Passenger side door power window regulator motor UP output
Ignition switch on (IG), front passenger window regulator switch UP
9 to 14 V
B (G3-3) - U (G3-4)
L - Y
Passenger side door power window regulator motor DOWN output
Ignition switch on (IG), front passenger window regulator switch off
Below 1 V
B (G3-3) - U (G3-4)
L - Y
Passenger side door power window regulator motor DOWN output
Ignition switch on (IG), front passenger window regulator switch DOWN
9 to 14 V
If the result is not as specified, there may be a malfunction.for RHD Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (H8-3) - D (H8-1)
L - W
Passenger side door power window regulator motor UP output
Ignition switch on (IG), front passenger window regulator switch off
Below 1 V
B (H8-3) - D (H8-1)
L - W
Passenger side door power window regulator motor UP output
Ignition switch on (IG), front passenger window regulator switch UP
9 to 14 V
B (H8-3) - U (H8-4)
L - P
Passenger side door power window regulator motor DOWN output
Ignition switch on (IG), front passenger window regulator switch off
Below 1 V
B (H8-3) - U (H8-4)
L - P
Passenger side door power window regulator motor DOWN output
Ignition switch on (IG), front passenger window regulator switch DOWN
9 to 14 V
| CHECK POWER WINDOW REGULATOR SWITCH (for Rear Door Side) |


Disconnect the J1 or I1 switch connectors.
Measure the voltage of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
B (3) - Body ground
L - Body ground
Ignition power supply
Ignition switch off
Below 1 V
B (3) - Body ground
L - Body ground
Ignition power supply
Ignition switch on (IG)
10 to 14 V
U (4) - Body ground
R - Body ground
Power window motor UP output
Ignition switch on (IG), power window switch off → UP
Below 1 V → 10 to 14 V
D (1) - Body ground
G - Body ground
Power window motor DOWN output
Ignition switch on (IG), power window switch off → DOWN
Below 1 V → 10 to 14 V
SU (5) - Body ground
G - Body ground
Power window motor UP input (Remote)
Ignition switch on (IG), power window master switch off → UP (Remote)
Below 1 V → 10 to 14 V
SD (2) - Body ground
BR - Body ground
Power window motor DOWN input (Remote)
Ignition switch on (IG), power window master switch off → UP (Remote)
Below 1 V → 10 to 14 V
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |


Disconnect the IA, IB and IE junction block connectors.
Disconnect the E18 ECU connector.
Measure the voltage and resistance of the wire harness side connectors.
*1: for LHDSymbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BECU (IB-30) - GND1 (IE-17)
R - W-B
Battery (power supply)
Always
9 to 14 V
IG (IM-9) - GND1 (IE-17)
W - W-B
Ignition power supply
Ignition switch on (IG)
9 to 14 V
IG (IM-9) - GND1 (IE-17)
W - W-B
Ignition power supply
Ignition switch off
Below 1 V
DCTY (IA-21) - Body ground*1
W - Body ground
Driver side door courtesy light switch input
Driver side door closed
10 kΩ or higher
DCTY (IA-21) - Body ground*1
W - Body ground
Driver side door courtesy light switch input
Driver side door open
Below 1 Ω
PCTY (IC-14) - Body ground*1
BR - Body ground
Front passenger side door courtesy light switch input
Front passenger side door closed
10 kΩ or higher
PCTY (IC-14) - Body ground*1
BR - Body ground
Front passenger side door courtesy light switch input
Front passenger side door open
Below 1 Ω
DCTY (IC-6) - Body ground*2
BR - Body ground
Driver side door courtesy light switch input
Driver side door closed
10 kΩ or higher
DCTY (IC-6) - Body ground*2
BR - Body ground
Driver side door courtesy light switch input
Driver side door open
Below 1 Ω
PCTY (IA-24) - Body ground*2
W - Body ground
Front passenger side door courtesy light switch input
Front passenger side door closed
10 kΩ or higher
PCTY (IA-24) - Body ground*2
W - Body ground
Front passenger side door courtesy light switch input
Front passenger side door open
Below 1 Ω
LIN2 (E18-23) - Body ground
V - Body ground
LIN communication
Always
10 kΩ or higher
GND1 (IE-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
*2: for RHD
If the result is not as specified, there may be a malfunction on the wire harness side.