2005-2008 RAV4 · Service Manual ENGINE

P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

CAUTION / NOTICE / HINT

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P2195 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2A00
Calculated value of air-fuel ratio (A/F) sensor response rate deterioration level less than threshold
(2 trip detection logic)
  1. Open or short in A/F sensor circuit
  2. A/F sensor
  3. ECM

MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after the preconditions are met in order to measure the A/F sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount, based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the A/F sensor response rate. The ECM receives a signal from the A/F sensor while performing active A/F control and uses it to calculate the A/F sensor response rate deterioration level.
If the A/F sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and sets the DTC.
A115363E03

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation pattern will activate the A/F sensor response monitor.

A115372E20

  1. A128727
    (a) Connect the intelligent tester to the DLC3.
  2. (b) Turn the ignition switch on (IG).
  3. (c) Turn the tester ON.
  4. (d) Clear DTCs (if set) (Click here).
  5. (e) Select the following menu items: Powertrain / Engine and ECT / Data List / Monitor Status.
  6. (f) Check that O2S(A/FS) Monitor is Incmpl.
  7. (g) Start the engine and warm it up.
  8. (h) Drive the vehicle at a constant speed of between 25 mph and 75 mph (40 km/h and 120 km/h) for 3 minutes.
  9. (i) Check that the status of the O2S(A/FS) Monitor is Compl.
  10. (j) Select the following menu items: Powertrain / Engine and ECT / DTC.
  11. (k) Check if any DTCs (any pending DTCs) are set.

WIRING DIAGRAM

A127851E01

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.

  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and turn the tester ON.
  3. (c) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. (d) On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  5. (e) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (f) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. The sensors react in accordance with increases and decreases in the fuel injection volume.

      Standard:
      Tester Display
      (Sensor)
      Injection Volume
      Status
      Voltage
      AFS B1 S1
      (A/F)
      +25%
      Rich
      Less than 3.0
      -12.5%
      Lean
      More than 3.35
      O2S B1 S2
      (HO2)
      +25%
      Rich
      More than 0.5
      -12.5%
      Lean
      Less than 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
2
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost
no reaction
A103185
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
3
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
Almost
no reaction
A103185
4
Injection volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system
(Air-fuel ratio extremely lean or rich)
Output Voltage
Almost
no reaction
A103185
Output voltage
Almost
no reaction
A103185
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Enter / View / AFS B1 S1 and O2S B1 S2.

HINT:
  1. DTC P2A00 may be set when the air-fuel ratio is stuck rich or lean.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2A00
    A
    P2A00 and other DTCs
    B

    If any DTCs relating to the A/F sensor (DTCs for the A/F sensor heater or A/F sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)
A052607E27
  1. Disconnect the B7 A/F sensor connector.

  1. Measure the resistance of the A/F sensor connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    HA1A (1) - +B (2)
    1.8 Ω to 3.4 Ω at 20°C (68°F)
    HA1A (1) - A1A- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR-FUEL RATIO SENSOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - AIR-FUEL RATIO SENSOR)
A127715E04
  1. Disconnect the B7 A/F sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    HA1A (B7-1) - HA1A (B32-109)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    HA1A (B7-1) or HA1A (B32-109) - Body ground
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2A00
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A


6. REPLACE AIR-FUEL RATIO SENSOR

NEXT


7. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P2A00
    B



B
REPLACE ECM
A

END


← P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (Nov 2005 – Dec 2006)P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (from Aug 2007) →