INSTALLATION
Removal / installation · Vehicles built from Aug 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1. INSTALL ANTENNA CORD SUB-ASSEMBLY |
for Short Body (w/o Sliding Roof):
Apply new double-sided tape as shown in the illustration.
- HINT:
- There are no installation markings in area A in the illustration. Therefore, apply the double-sided tape toward point A.
Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
- HINT:
- Place any extra antenna cord length in the surplus cord area shown in the illustration.
Apply tape to both ends of the antenna cord to fix the cord in place.


for Short Body (w/ Sliding Roof):
Apply new double-sided tape as shown in the illustration.
- HINT:
- There are no installation markings in area A in the illustration. Therefore, apply the double-sided tape toward point A.
Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
- HINT:
- Place any extra antenna cord length in the surplus cord area shown in the illustration.
Apply tape to both ends of the antenna cord to fix the cord in place.


for Long Body (w/o Sliding Roof):
Apply new double-sided tape as shown in the illustration.
- HINT:
- There are no installation markings in area A in the illustration. Therefore, apply the double-sided tape toward point A.
Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
- HINT:
- Place any extra antenna cord length in the surplus cord area shown in the illustration.
Apply tape to both ends of the antenna cord to fix the cord in place.


for Long Body (w/ Sliding Roof):
Apply new double-sided tape as shown in the illustration.
- HINT:
- There are no installation markings in area A in the illustration. Therefore, apply the double-sided tape toward point A.
Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
- HINT:
- Place any extra antenna cord length in the surplus cord area shown in the illustration.
Apply tape to both ends of the antenna cord to fix the cord in place.


| 2. INSTALL ROOF HEADLINING ASSEMBLY (for Long Body) |
Install the roof headlining (Click here).
| 3. INSTALL ROOF HEADLINING ASSEMBLY (for Short Body) |
Install the roof headlining (Click here).
| 4. INSTALL ANTENNA CORD SUB-ASSEMBLY |
Install the antenna cord with the 4 clamps.
Connect the connector.


| 5. INSTALL UPPER INSTRUMENT PANEL |
Attach the 6 clips and 5 claws to install the instrument panel.
Connect the connectors and clamps.
Install the 2 bolts and 2 screws.


Connect the passenger airbag connector.
Install the 2 bolts to the passenger airbag.

- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
| 6. INSTALL FRONT PILLAR GARNISH LH |
for Long Body (Click here)
| 7. INSTALL FRONT PILLAR GARNISH RH |
for Long Body (Click here)
| 8. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() ![]() |
Attach the 2 hinges to install the door.
Attach the claw to the glove compartment door stopper.

While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
| 9. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY CENTER |
![]() ![]() |
Attach the 5 clips to install the instrument panel register.
| 10. INSTALL STEREO OPENING COVER (w/o Radio Receiver) |
![]() ![]() |
Attach the 4 clips to install the stereo opening cover.
Install the 4 bolts.
| 11. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver) |
Remove the radio receiver assembly with bracket. (Click here).
| 12. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() ![]() |
Connect the connector.
Attach the 3 clips and 3 claws to install the cluster finish panel.
| 13. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() ![]() |
Connect the connector.
Attach the 3 clips and 3 claws to install the cluster finish panel.
| 14. INSTALL COMBINATION METER ASSEMBLY |
![]() ![]() |
Connect the connector.
Attach the 2 clips to install the combination meter.
Install the 2 screws.
| 15. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() ![]() |
Attach the 4 clips and 6 claws to install the instrument cluster finish panel.
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |







