2005-2008 RAV4 · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

  1. C113576
    Remove the clutch release fork with clutch release bearing from the transaxle case.


2. REMOVE CLUTCH RELEASE BEARING ASSEMBLY

  1. C116601
    Remove the clutch release bearing and clutch release bearing hub from the release fork.


3. REMOVE RELEASE FORK SUPPORT

  1. C113601
    Remove the release fork support from the transaxle case.


4. REMOVE CLUTCH RELEASE FORK BOOT

  1. C113599
    Remove the clutch release fork boot from the transaxle case.


5. REMOVE FLOOR SHIFT CONTROL LEVER HOUSING SUPPORT BRACKET

  1. C115444
    Remove the 3 bolts and floor shift control lever housing support bracket from the manual transaxle.


6. REMOVE SELECTING BELL CRANK ASSEMBLY

  1. C112480
    Remove the 2 bolts and selecting bell crank from the transmission case.


7. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

  1. C112471E02
    Using SST, remove the back-up light switch and gasket.
    SST
    09816-30010  


8. REMOVE NO. 1 LOCK BALL ASSEMBLY

  1. C116559
    Remove the lock ball from the transmission case.


9. REMOVE NO. 2 LOCK BALL ASSEMBLY

  1. C116599
    Remove the lock ball from the transmission case.


10. REMOVE SHIFT GATE PIN

  1. C116598
    Remove the shift gate pin from the transmission case.


11. REMOVE CONTROL SHAFT COVER

  1. C112484
    Remove the 4 bolts and control shaft cover from the transmission case.


12. REMOVE SHIFT AND SELECT PIN

  1. C117499E01
    While pressing the shift and select pin (*1) in as much as possible, pull the shift and select pin (*2).

  1. Remove the spring.


13. REMOVE O-RING

  1. C117500E01
    Remove the O-ring from the shift and select pin.


14. REMOVE MANUAL TRANSMISSION FILLER PLUG

  1. C113635
    Remove the transmission filler plug and gasket from the transmission case.


15. REMOVE DRAIN PLUG

  1. C113634
    Remove the drain plug and gasket from the front transaxle case.


16. REMOVE SHIFT DETENT BALL

  1. C113593
    Using a hexagon wrench, remove the 4 shift detent ball plugs from the front transaxle case.

  1. Using a magnetic finger, remove the 4 spring seats and balls.


17. REMOVE REVERSE IDLER GEAR SHAFT BOLT

  1. C116545
    Remove the reverse idler gear shaft bolt and reverse idler gear shaft gasket from the transmission case.


18. REMOVE MANUAL TRANSMISSION CASE PLUG

  1. C116543E01
    Remove the transmission case plugs from the transmission case.


19. REMOVE MANUAL TRANSMISSION CASE

  1. C113600
    Remove the 6 bolts from the front transaxle case side.

  1. C113610
    Remove the 12 bolts from the transmission case side.

  1. C116542
    Use 2 snap ring pliers to keep the snap ring stretched and remove the transmission case.


20. REMOVE NO. 1 OIL RECEIVER PIPE

  1. C113590
    Remove the receiver pipe from the transmission case.

    NOTICE:
    Do not damage the No. 1 oil receiver pipe.


21. REMOVE TRANSMISSION OIL SEPARATOR

  1. C115450E01
    Remove the 2 bolts and oil separator from the transmission case.


22. REMOVE 1ST AND 2ND SHIFT FORK SHAFT

  1. C115434
    Remove the bolt of the 1st and 2nd shift fork shaft.

  1. C116327
    Remove the 1st and 2nd shift fork shaft.


23. REMOVE 3RD AND 4TH SHIFT FORK SHAFT

  1. C117839
    Using a pin punch and hammer, tap out the slotted spring pin from the No. 2 gear shift head.

  1. C117840
    Using a pin punch and hammer, tap out the slotted spring pin from the No. 2 gear shaft fork.

  1. C115438E02
    Remove the 3rd and 4th shift fork shaft and No. 2 gear shift head.


24. REMOVE NO. 2 GEAR SHIFT FORK

  1. C115439
    Remove the No. 2 gear shift fork from the No. 1 output shaft.


25. REMOVE NO. 5 GEAR SHIFT FORK SHAFT

  1. C115440
    Using a screwdriver, pry out the E-ring from the front transaxle case.

  1. C115441
    Remove the pin from the front transaxle case.

  1. C115442
    Remove the No. 5 shift fork shaft from the front transaxle case.

  1. C113585
    Using a pin punch and hammer, tap out the slotted spring pin.

  1. Remove the No. 3 gear shift head.


26. REMOVE NO. 1 GEAR SHIFT FORK

  1. C115443
    Remove the No. 1 gear shift fork from the No. 1 output shaft.


27. REMOVE SHIFT ARM

  1. C116744
    Remove the shift arm from the front transaxle case.


28. REMOVE REVERSE SHIFT FORK SHAFT

  1. C115428
    Remove the bolt of the reverse shift fork shaft.

  1. C115429
    Remove the reverse shift fork shaft.


29. REMOVE 5TH AND 6TH SHIFT FORK SHAFT

  1. C115430
    Remove the bolt of the No. 3 gear shift fork.

  1. C115431
    Remove the 5th and 6th shift fork shaft.


30. REMOVE NO. 3 GEAR SHIFT FORK

  1. C116328
    Remove the No. 3 gear shift fork from the No. 2 output shaft.


31. REMOVE REVERSE SHIFT FORK

  1. C115432
    Remove the reverse shift fork from the No. 2 output shaft.


32. INSPECT REVERSE IDLER GEAR THRUST CLEARANCE

  1. C113642
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.40 to 1.05 mm (0.0016 to 0.0413 in.)

    Maximum clearance:
    1.05 mm (0.0413 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear, needle roller bearing and reverse idler gear shaft.


33. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

  1. C113646
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.048 mm (0.0006 to 0.0019 in.)

    Maximum clearance:
    0.048 mm (0.0019 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear, needle roller bearing and reverse idler gear shaft.


34. REMOVE REVERSE IDLER GEAR

  1. C113637E01
    Remove the reverse idler gear shaft by sliding and lifting it.

  1. C116557
    Remove the reverse idler gear, needle roller bearing and reverse idler thrust washer from the reverse idler gear shaft.


35. REMOVE INPUT SHAFT, NO. 1 OUTPUT SHAFT AND NO. 2 OUTPUT SHAFT

  1. C116196
    Remove the 3 shafts at the same time.


36. REMOVE TRANSMISSION OIL SEPARATOR

  1. C115451E02
    Remove the 2 bolts and oil separator from the front transaxle case.


37. REMOVE FRONT DIFFERENTIAL CASE ASSEMBLY

  1. C115412
    Remove the differential case from the front transaxle case.


38. REMOVE TRANSMISSION MAGNET

  1. C115449
    Remove the transmission magnet from the front transaxle case.


39. REMOVE NO. 2 OUTPUT SHAFT REAR BEARING OUTER RACE

  1. C113586E01
    Using SST, remove the outer race the transmission case.
    SST
    09387-00041   (09387-02020)


40. REMOVE OUTPUT SHAFT REAR BEARING SHIM

  1. C116565
    Remove the rear bearing shim from the transmission case.


41. REMOVE SHIFT FORK SHAFT BEARING

  1. C113594E01
    Using SST, remove the 4 shift fork shaft bearings from the transmission case.
    SST
    09612-65014  
    09387-00041   (09387-01021)
    09527-20011  


42. REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

  1. C113581E01
    Using SST, remove the shift and select lever shaft needle roller bearing from the transmission case.
    SST
    09612-65014  
    09387-00041   (09387-01021)


43. REMOVE INPUT SHAFT REAR BEARING SHAFT SNAP RING

  1. C116544
    Using snap ring pliers, remove the 2 snap rings.


44. REMOVE INPUT SHAFT FRONT BEARING

  1. C113584
    Remove the bolt from the front transaxle case.

  1. C113580E01
    Using SST, remove the input shaft bearing from the front transaxle case.
    SST
    09612-30012  


45. REMOVE TRANSAXLE CASE OIL SEAL

  1. C116577
    Using a screwdriver, pry out the transaxle case oil seal from the front transaxle case.


46. REMOVE OUTPUT SHAFT FRONT BEARING

  1. C113583
    Remove the bolt from the front transaxle case.

  1. C113597E01
    Using SST, remove the bearing from the front transaxle case.
    SST
    09612-65014   (09612-01020)


47. REMOVE OUTPUT SHAFT COVER

  1. C115453
    Remove the output shaft cover from the front transaxle case.


48. REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING OUTER RACE

  1. C113587E01
    Using SST, remove the outer race from the front transaxle case.
    SST
    09387-00041   (09387-02020)


49. REMOVE OUTPUT SHAFT COVER

  1. C115454
    Remove the output shaft cover from the front transaxle case.


50. REMOVE SHIFT FORK SHAFT BEARING

  1. C113595E01
    Using SST, remove the 4 bearings from the front transaxle case.
    SST
    09612-65014  
    09387-00041   (09387-01021)


51. REMOVE TRANSMISSION CASE OIL SEAL

  1. C116195
    Using a screwdriver, pry out the oil seal from the transmission case.


52. REMOVE FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING

  1. C116548
    Using a brass bar and hammer, tap out the front differential case rear outer race bearing and front differential case rear shim from the transmission case.


53. REMOVE TRANSAXLE CASE OIL SEAL

  1. C116194
    Using a screwdriver, pry out the oil seal from the front transaxle case.


54. REMOVE FRONT DIFFERENTIAL CASE FRONT OUTER RACE BEARING

  1. C113588E01
    Using SST, remove the outer race bearing from the front transaxle case.
    SST
    09387-00041   (09387-02020)

← COMPONENTS (from Nov 2005)REASSEMBLY (from Nov 2005) →