2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL FUEL SUPPLY PUMP ASSEMBLY
  1. Install a new O-ring to the fuel supply pump.

  1. Install the supply pump drive coupling.

    NOTICE:
    When reusing the coupling, it must be installed in the same orientation (top/bottom, front/back) as when it was removed.

    HINT:
    Line up the coupling with the groove in the camshaft end.

  1. Install the supply pump with the 2 bolts.

    Torque:
    21 N*m{ 209 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Apply engine oil on the O-ring of the supply pump.

    HINT:
    Line up the end of the supply pump drive shaft with the supply pump drive coupling.

  1. A110786
    Connect the suction control valve connector.

  1. Connect the fuel temperature sensor connector.


2. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
If the supply pump is replaced, the fuel inlet pipe must also be replaced.

  1. A114943E03
    Temporarily install the fuel inlet pipe with the 2 clamps and nut.

  1. Using SST, first tighten the nut at the common rail end of the fuel inlet pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 25 ft.*lbf } for use without SST

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Using SST, tighten the nut at the supply pump end of the fuel inlet pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 25 ft.*lbf } for use without SST

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Tighten the fuel inlet pipe clamp nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


3. INSTALL NO. 1 FUEL HOSE

  1. A114892
    Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 1 fuel hose.


4. INSTALL NO. 3 FUEL HOSE

  1. A114958E04
    Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 3 fuel hose.


5. INSTALL AIR CLEANER ASSEMBLY WITH ELEMENT

  1. A124928E01
    Install the cleaner case with the 3 bolts and connect the wire harness clamp.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air filter element.


6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A124929E01
    Insert the hinge parts of the air cleaner cap into the air cleaner case, and then hang the 3 hook clamps.

  1. Connect the mass air flow meter connector.

  1. Engage the wire harness clamp.


7. INSPECT FOR FUEL LEAK
  1. PERFORM ACTIVE TEST

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine.

    3. Turn the intelligent tester ON.

    4. Enter the following menus: Powertrain / Engine / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizing common rail internal fuel pressure, and checking for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when start is selected
      2. Above conditions to be maintained while test is started


8. BLEED AIR FROM FUEL SYSTEM

  1. A130544
    Using the hand pump, bleed air from the fuel system until pumping becomes difficult.


9. INSTALL NO. 1 ENGINE COVER

  1. A123518
    Attach the 4 clips to install the engine cover.


10. INITIALIZE THE LEARNING VALUE OF THE SUPPLY PUMP ASSEMBLY
  1. Perform initialization procedure (Click here).

← INSTALLATION (Nov 2005 – Dec 2006)INSTALLATION (from Aug 2007) →