2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL COMMON RAIL ASSEMBLY

  1. A114961E01
    Install the common rail assembly with the 2 bolts.

    Torque:
    21 N*m{ 209 kgf*cm , 15 ft.*lbf }

  1. Using pliers, grip the claws of the clip and slide the clip to connect the No. 4 fuel hose.


2. INSTALL NO. 1 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
In a case where the common rail is replaced, the injection pipes must also be replaced.

  1. A114941E01
    Temporarily install the 4 injection pipes.

  1. Using SST, first tighten the nut at the common rail end of the injection pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 25 ft.*lbf } for use without SST

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Using SST, tighten the nut at the injector end of the injection pipe.

    SST
    09023-12701  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 25 ft.*lbf } for use without SST

    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Install the 4 injection pipe clamps and 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


3. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
  1. In a case where the common rail is replaced, the fuel inlet pipe must also be replaced.

  1. A114943E03
    Temporarily install the fuel inlet pipe with the 2 clamps and nut.

  1. Using SST, tighten the nut at the common rail end of the fuel inlet pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 25 ft.*lbf } for use without SST

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Using SST, tighten the nut at the supply pump end of the fuel inlet pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    34 N*m{ 347 kgf*cm , 25 ft.*lbf } for use without SST

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Tighten the fuel inlet pipe clamp nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


4. INSTALL ENGINE WIRE

A126799
  1. Connect the engine wire to the wire bracket with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the engine wire to the engine cover bracket with the bolt and 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the pressure sensor connector and 2 clamps.

  1. Connect the common rail connector.

  1. Connect the glow plug wire harness with the nut and grommet.

    Torque:
    2.2 N*m{ 22 kgf*cm , 19 in.*lbf }

  1. Connect the 4 injector connectors and install the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the vacuum regulating valve connector and 2clamps.

  1. Connect the 2 injector driver connectors and clamp.

  1. Install the nut and connect the 3 sensor connectors, 2 clamps and generator wire.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


5. BLEED AIR FROM FUEL SYSTEM

  1. A130544
    Using the hand pump, bleed air from the fuel system until pumping becomes difficult.


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

7. CHECK FOR FUEL LEAKS
  1. PERFORM ACTIVE TEST

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine.

    3. Turn the intelligent tester ON.

    4. Enter the following menus: Powertrain / Engine / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizing common rail internal fuel pressure, and checking for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when start is selected
      2. Above conditions to be maintained while test is started


8. INSTALL NO. 1 ENGINE COVER

  1. A123518
    Attach the 4 clips to install the engine cover.

← INSPECTION (from Nov 2005)INSTALLATION (Jan 2007 – Jul 2007) →